Scotsman ECC0800-32E Скачать руководство пользователя страница 24

Страница: 24 / 32

EH222 E and Condensing Unit

Remote Low Side Cuber User Manual

June 2017

Page 24

Operational Characteristics 800 lb system

Cycle Times @ Condenser Temp/Cabinet Temp/Water Temp in degrees F.

-20/50/40

70/70/50

90/90/70

120/110/100

Freeze

9 to 10 minutes

10 to 12 minutes

13 to 15 minutes

19 to 21 minutes

Harvest

2 to 3 minutes

1 to 1.5 minutes

.5 to 1 minute

System Pressures @ Condenser Temp/Cabinet Temp/Water Temp in degrees F

-20/50/40

70/70/50

90/90/70

120/110/100

Suction at head, end of Freeze 26 to 27 PSIG

26 to 31 PSIG

30 to 35 PSIG

Suction at head, Harvest - Peak 88 PSIG

85 to 105 PSIG

105 to 125 PSIG 140 t0 160 PSIG

Discharge at Condensing Unit:

Freeze - 5 minutes in

217 PSIG

230 to 250 PSIG 250 to 270 PSIG 330 to 350 PSIG

Operational Characteristics 1000 lb system

Cycle Times @ Condenser Temp/Cabinet Temp/Water Temp in degrees F.

20/70/40

70/70/50

90/90/70

120/110/100

Freeze

7 to 8 minutes

8 to 9 minutes

10 to 11 minutes

16 to 18 minutes

Harvest

2 to 3 minutes

1 to 1.5 minutes

.5 to 1 minute

System Pressures @ Condenser Temp/Cabinet Temp/Water Temp in degrees F

-20/50/40

70/70/50

90/90/70

120/110/100

Suction at head, end of Freeze 22 PSIG

26 to 31 PSIG

27 to 32 PSIG

30 to 35 PSIG

Suction at head, Harvest - Peak 88 PSIG

85 to 105 PSIG 90 to 110 PSIG 140 to 160 PSIG

Discharge at Condensing Unit:

Freeze - 5 minutes in

219 PSIG

230 to 250 PSIG 240 to 250 PSIG 345 to 380 PSIG

Below information applies to both size systems:

Headmaster maintains a minimum discharge pressure during freeze of 217 PSIG + 25, -15 PSIG.

CPR Valve Setting: 55 - 60 PSIG.

Note: CPR allows a maximum low side pressure at the compressor. Maximum only occurs during harvest.

Refrigerant Charge

• 800: 192 oz.
• 1000: 248 oz

Compressor Amps, 800 model

• Single Phase - 6 to 8 Three Phase - 5 to 7

Compressor Amps, 1000 model

• Single Phase - 8 to 9, Three Phase - 6.3 to 5.2

Batch Weight: 8 lb

Discharge Pressure Cut Out Switch

• Cuts Out at: 450 PSIG Resets at: 350 PSIG

Содержание ECC0800-32E

































Результаты поиска

Содержание ECC0800-32E

Отзывы:

Похожие инструкции для ECC0800-32E

Бренды по названию

Популярные бренды

Scotsman ECC0800-32E, Инструкция по установке и эксплуатации

Результаты поиска

Содержание ECC0800-32E

Отзывы:

Похожие инструкции для ECC0800-32E

Бренды по названию

Популярные бренды