background image

Final Check List

1. Is the unit in a room where ambient
temperatures are above a minimum of 10oC (50

o

F)

even in winter months?

2. Is there at least a 15 cm (6") clearance around
the unit for proper air circulation?

3. Is the unit level? (IMPORTANT)

4. Have all the electrical and plumbing connections
been made, and is the water supply shut-off valve
open?

5. Has the voltage been tested and checked
against the data plate rating?

6. Has the water supply pressure been checked to
ensure a water pressure of at least 20 psi.

7. Check all refrigerant lines and conduit lines to
guard against vibrations and possible failure.

8. Have the bolts holding the compressor down
been checked to ensure that the compressor is
snugly fitted onto the mounting pads?

9. Have the bin liner and cabinet been wiped
clean?

10. Has the owner/user been given the User
Manual and been instructed on the importance of
periodic maintenance checks?

11. Has the Manufacturer’s registration card been
filled in properly? Check for correct model and
serial number against the serial plate and mail the
registration card to the factory.

12. Has the owner been given the name and the
phone number of the authorized SCOTSMAN
Service Agency serving him?

CU0515

April 2007

Page 5

Содержание CU0515

















Отзывы: