Scotsman CMS1202R Скачать руководство пользователя | Manualshive

Страница: 15 / 27

background image

COMPONENT DESCRIPTION

Bin Level Control

This electronic control uses sound waves to
measure the distance between the bottom of the
ice machine and the top of the ice in the bin. It is
designed to control the machine’s ice production to
maintain that distance.

The control is adjustable so that the ice machine
will maintain a certain height of ice. When set at
FULL it will not allow the machine to fill the bin any
closer to the ice machine than about 8", and it will
not work if the distance to the bottom of the bin is
greater than 8 feet.

Because it uses sound waves, a slight “ticking”
sound can be heard coming from the bottom of the
machine.

There are three parts to the control, the
transducer, the circuit board, and the ice level
control switch.

FULL

SOUND WAVES

PARTIAL

BIN ICE LEVEL

SELECTOR

SWITCH

THE USER CAN

SELECT THE

AMOUNT OF ICE TO

BE MAINTAINED IN

THE BIN.

ICE/OFF/WASH SWITCH

CMS1202R

September 1993

Page 15

«
...
13
14
15
16
17
...
»

Содержание CMS1202R




























Отзывы:

Нет отзывов

Похожие инструкции для CMS1202R

Бренд: G3 Ferrari Страницы: 12

Primula SPEAK & BREW SAB-3001

Бренд: Epoca Страницы: 8

Бренд: Krups Страницы: 16

Бренд: Handpresso Страницы: 110

Бренд: Faema Страницы: 50

Бренд: Gaggia Страницы: 78

Бренд: DeLonghi Страницы: 22

Бренд: Saeco Страницы: 40

IMPRESSA J9 One Touch

Бренд: Jura Страницы: 52

Бренд: T-Fal Страницы: 36

Бренд: Team Kalorik Страницы: 44

Бренд: PALSON Страницы: 29

Бренд: B.F.C. Страницы: 32

MULTY P TTi Series

Бренд: Valmar Страницы: 141

Бренд: UFESA Страницы: 200

Бренд: iDPRT Страницы: 2

Бренд: AMW Страницы: 2

Бренд: NEFF Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды