background image

FCC STATEMENT 

This equipment has been tested and found to comply with the limits for a WPC device, 

pursuant to  Part 18  of  the  FCC  Rules.  These limits are designed to provide reasonable 

protection against harmful interference in a residential installation. 

CAUTION:  Changes or modifications not expressly approved by the party responsible 

for compliance could void the user's authority to operate the product. 

NOTE: This equipment has been tested and found to comply with the limits for a wireless 

power charger, pursuant to Part 18 of the FCC Rules. These limits are designed to provide 

reasonable  protection  against  harmful  interference  in  a  residential  installation.  This 

equipment generated,  uses and can radiate radio frequency energy and,  if not installed 

and  used  in  accordance  with  the  instructions,  may cause  harmful  interference  to  radio 

communications. However there is no guarantee that interference will occur in a particular 

installation.  If  this  equipment  does  cause  harmful  interference  to  radio  or  television 

reception,  which  can  be  determined 

by 

turning  the  equipment  off  and  on,  the  user  in 

encouraged to try to correct the interference by one or more of the following measures: 

•  Reorient or relocate the receiving antenna. 

•  Increase the separation between the equipment and receiver. 

•  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the 

receiver is connected. 

•  Consult the dealer or an experienced radio/TV technician for help. 

FCC STATEMENT 

This device complies with industry Canada License-exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this device may not cause interference, and (2) 

this device must accept any interference, including interference that may cause undesired 

operation  of  the  device.  This  equipment complies with  IC  RSS-102  radiation  exposure 

limits set forth for an uncontrolled environment. This transmitter must not be co-located 

or operated in conjunction with any other antenna or transmitter. 

For complete warranty details or questions 

visit us online at www.scosche.com or contact us at: 

www.scosche.com/contact 

[email protected] 

1 (BOO) 363-4490 ext.1 

12 

Содержание TAQ04













Отзывы: