Scopus CODICO IRD-2600 Скачать руководство пользователя страница 76

Страница: 76 / 134

User Manual

Chapter 3. Operation

Page 3-28

P/N 2349-72784-00

Table 3-9:

System Configuration Menu Options

OPTION

DESCRIPTION

Session Word

Session Word Setup
Sets the session word for BISS encryption word value (8 digits Hex word),
for all BISS CA encryption modes

NOTE

This option is

NOT

available when the EVEN-ODD

DSNG-CA Encryption mode is selected.

ODD/EVEN Key

Odd / Even Key Setup.
Sets the key value (64 bit word), for the ODD/EVEN CA Encryption mode.

NOTE

This option is available

ONLY

when the EVEN-ODD

DSNG-CA Encryption mode is selected.
It is

NOT

available when any of the BISS CA Encryption modes are

activated.

Injected ID

BISS-E – Injected ID Word Setup.
Sets the word value (56 bit word), for the BISS-E / Injected ID mode.

NOTE

T this option is available

ONLY

when the BISS-E / Injected ID DSNG-CA

Encryption mode is selected.
It is

NOT

available when any of the other DSNG-CA Encryption modes are

activated.

Содержание CODICO IRD-2600







































































































































Результаты поиска

Содержание CODICO IRD-2600

Отзывы:

Бренды по названию

Популярные бренды

Scopus CODICO IRD-2600, Руководство пользователя

Результаты поиска

Содержание CODICO IRD-2600

Отзывы:

Бренды по названию

Популярные бренды