Scopus CODICO IRD-2600 Скачать руководство пользователя страница 49

IRD-2600 / IRD-2800 
Integrated Receiver Decoders 

 

 

P/N 2349-72784-00 

 

Page 3-1  

 

3. 

OPERATION 

3.1. 

Introduction 

This chapter describes the procedures required for the operation of the IRD-2600 and 
IRD-2800 Integrated Receiver Decoders. 

In addition to the Operation Guide, the following manuals are available for Terminal Control 
of the IRD: 

Basic Terminal Control Protocol (P/N 2349-72175-03.1) 
Advanced Terminal Control Protocol (P/N 2349-72175-03.2) 
Master-Slave Terminal Control Protocol (P/N 2349-72175-03.3) 

3.1.1. 

IRD Operation and Management 

Both IRD-2600 and IRD-2800 Integrated Receiver Decoders can be manually managed 
from the IRD Front Control Panel, locally by a PC Terminal or remotely, from the Uplink 
through the incoming Bit Stream. 

Manual management of the IRD is provided from the IRD Front Control Panel by the 
keypad on the panel, or by using an optional Infrared Remote Control. The LCD on the 
panel displays the menus and options of the IRD embedded software.  
The Infrared Remote Control can be ordered through a local SCOPUS Network 
Technologies Ltd. product supplier. 

Management from the Uplink is achieved with the CODICO

®

 NMS-4000 Network 

Management System. Management from the PC Terminal requires a serial line (RS-232) 
communication cable to be connected between the IRD and a communication port on the 
PC. The Terminal Control software is a command line prompt accessible via any PC with 
Terminal Software installed. For details, refer to Chapter  2 above. 

Содержание CODICO IRD-2600







































































































































Отзывы: