manualshive.com logo in svg

scigiene SP-850055, Инструкция по эксплуатации

Поделиться
Скачать
scigiene SP-850055 Скачать руководство пользователя страница 19

 

 

PC CONNECTION  

The  meter  can  interface  with  a  personal  computer  to  capture 
on-line or stored data.  

Connection procedures:  

1. Plug the USB cable into the cable jack on the side of the meter.  

2.  Plug  D-sub  9  pin  type  connector  into  a  computer  Serial  COM  port.  
  COM ports 1-8 can be used.  

3.  Insert  CD-Rom  in  computer  and  follow  the  procedure  in  the  
  operation manual located on the CD.  

Protocol information  

USB  protocol  settings:  9600  bps,  8  data  bits,  no  parity. 
(Transmits ASCII code every second.)  

Normal Data:  

pxx.xxpH:  mxx.xxmV:Txxx.xC(F)@  2007-04-18 

18:48:48LRCCRLF  

Protocol Information  

Errors:  

ExxNul:  ExxNul:  ExxNul  @  2007-04-18 

18:48:48LRCCRLF  

Description:  

$pH:mV:TpH LRC CRLF  

Note...  

The first value is pH reading in pH, the second value is  
Voltage reading in mV, the third value is Temperature of pH probe in C/F, 
and 

“x” is a numerical value.  

 
 
 
 
 
 
 
 
 
 
 
 

19  

Содержание SP-850055

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды