Schulte Titan 5000 II Series Скачать руководство пользователя страница 98 | Manualshive

Страница: 98 / 108

Schulte Titan 5000 II Series Скачать руководство пользователя страница 98

MAINTENANCE

Titan 5000 Series II 01/22

Maintenance Section 5-2

© 2022 Alamo Group Inc.

MAINTENANCE

NOTE:

Experience has shown that the majority of breakdowns are the result of inadequate or improper service

and inspection.

DRIVE COUPLER

The Titan 5000 is equipped with a zero maintenance direct-drive Magnaloy Hytrel Coupler system which is
designed to provide years of heavy duty service.
Motor and Coupler Install Instructions:
1. Slide the Steel Bushing Coupler Half (R800-228) onto

the reel shaft ensuring good engagement with the key in
the reel shaft.

2. With the motor (116-216) secured to the motor mount

(R800-226), slide the Motor Coupler Half (R800-229)
onto the motor shaft inside the housing ensuring good
engagement with the key in the motor shaft.

3. Rest the Hytrel Coupler Insert (R800-227) in the Steel

Bushing Coupler Half that is mounted on the Reel.

4. Lift the Motor Assembly and connect the coupler halves

with the Hytrel insert between them.

5. Using four (4) ¾"x2-1/2" carriage bolts and ¾" flange lock nuts snug the motor mount to the reel side plate,

but do not fully tighten.

6. Push the Reel side coupler half towards the motor until the two halves contact the lip around the outside of

the insert. Do not push the Motor side coupler further than necessary onto the motor shaft.

7. Using Loctite 243, tighten all set screws on both coupler halves to 25.5 ft/lbs (35 Nm).

8. Using the four (4) ¼" bolts and jam nuts installed to the adjustment plates on the reel side plate, align the

outer surfaces of the coupler halves to within 0.015".. Measure this using a straight edge across the
coupler halves. Measure in two places 90 degrees from each other as shown (for example: top and front
of the coupler)

9. Rotate the reel to ensure good engagement all around the coupler insert.

NOTE:

Coupler misalignment of greater than 1 degree, or 0.015" will reduce the life of the coupler insert and

may cause damage to other components of your rock picker.

«
...
96
97
98
99
100
...
»

Содержание Titan 5000 II Series













































































































Отзывы:

Нет отзывов