Schulte Titan 5000 II Series Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 108

Schulte Titan 5000 II Series Скачать руководство пользователя страница 75

OPERATION

Titan 5000 Series II 01/22

Operation Section 4-13

© 2022 Alamo Group Inc.

OPERA

T

ION

7.2 Rock Picker Pre-Operation Inspection/Service

Before each implement use, a complete inspection and service is required to ensure the implement is in a
good and safe working condition. Damaged and/or broken parts should be repaired and/or replaced
immediately. To ensure the implement is ready for operation, conduct the following.

7.1 Tractor Pre-Operation Inspection/Service

Refer to the tractor operator’s manual to ensure a
complete pre-operation inspection and scheduled
service is performed according to the
manufacturers recommendations. The following
are some of the items that require daily service and
inspection:

•

Tire condition/air pressure

•

Wheel lug bolts

•

Steering linkage

•

PTO shield

•

SMV sign is clean and visible

•

Tractor’s lights are clean and functional

•

Tractor Seat belt is in good condition

•

Tractor ROPS is in good condition

•

ROPS is in the raised position

•

No tractor oil leaks

•

Radiator free of debris

•

Engine oil level and condition

•

Engine coolant level and condition

•

Power brake fluid level

•

Power steering fluid level

•

Fuel condition and level

•

Sufficient lubrication at all lube points

•

Air filter condition

OPS-U-0030

The operator’s manual and safety signs affixed on
the unit contain important instructions on the safe
and proper use of the equipment. Maintain these
important safety features on the implement in good
condition to ensure the information is available to
the operator at all times.

•

Ensure the manual canister is secured to the
equipment with the operator’s manual inside.

•

Ensure all safety signs are in place and legible.
Replace missing, damaged, and illegible
decals.

OPS-U- 0011

«
...
73
74
75
76
77
...
»

Содержание Titan 5000 II Series













































































































Отзывы:

Нет отзывов