manualshive.com logo in svg

Schonstedt Loki Contractor, Руководство пользователя

Поделиться
Скачать
Schonstedt Loki Contractor Скачать руководство пользователя страница 3

2

Loki Models

Two Loki models are available. The models are designed around the 
needs of contractors and utility companies who need to detect utilities for 

safe and efficient excavation and repair. 

Contractor Model

Optimized for excavation and construction contractors, 
the contractor model has 512 Hz, 8 kHz and 131 
kHz frequencies built within the Loki transmitter. The 

higher frequency 131 kHz can be used to find well-

insulated, high impedance utilities such as twisted-
pair telecom cables or insulated pipe joints. A lower 
frequency of 512 Hz is also built in to support the long 
range locating of lower impedance cables, such as 
power lines.

Utilities Model

Built for the challenge of detecting and tracing buried 
water/drain pipes and telecom ducts, the low 512 Hz 
frequency can be used to trace metallic pipes. The 
higher 82 kHz frequency can support the detection 
of jointed pipes, non-metallic pipes and ducts (when 
there’s a metallic trace wire). The utility model can 
also be used to locate multiple sonde frequencies. 

OPTIMIZED FOR

UTILITIES

OPTIMIZED FOR

CONTRACTORS

Содержание Loki Contractor

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды