manualshive.com logo in svg

Schonstedt Loki Contractor, Руководство пользователя

Поделиться
Скачать
Schonstedt Loki Contractor Скачать руководство пользователя страница 17

16

7.  Measure the distance between points A and B and multiply by 0.7 to give an 

approximate depth measurement.

Warnings

Signal Overload

If the Loki receiver is used in areas where very large power signals are present, 

the signal bar graph will flash. In this condition the sensitivity control and depth 

function will not operate and you are advised to try lifting the Loki receiver to bring 
it out of the overloaded condition or use in a different location.

Deactivating

If required the Shallow

Alert™

 warnings can be temporarily disabled by pressing 

and holding the frequency selection button for the duration of the battery test bleep 
at switch on.

Live Plug Connector

  Do not use the supplied Direct Connect leads to connect to live cables. Use 

the Live Plug Connector or Live Cable Connector. Failure to do so may result in 
injury or equipment damage.

  Connection to live power cables should only be undertaken by qualified personnel.

The optional Live Plug Connector applies the transmitter signal to a live domestic 
power socket and via the domestic wiring system on the service cable and the 
supply cable in the street. The signal should be detectable on the supply system to 
a few hundred meters each side of the point of application.

Note: Do not connect the Loki transmitter to live cables without using a Live Plug 
Connector or Live Cable Connector.

Содержание Loki Contractor

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды