manualshive.com logo in svg

Schmidt MV3, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Schmidt MV3 Скачать руководство пользователя страница 50

  

 

50 

Copyright © 2021 Axxiom Manufacturing, Inc. 

 

8.12 

VBS II  Blowdown System:

  Remove  monthly and check for internal wear of components. 

Replace worn components as needed. See drawing in Section 9.10. 

 

 

8.13 

PPE:

 

Check daily to verify that all personal protective equipment is available for each blast 

operator. Check daily to verify that  all  personal protective equipment is in good operating 

condition. Consult the operating and maintenance instructions provided by the manufacturer of 

each PPE item. See Section 3.10 and reference OSHA 29 CFR 1910 Subpart I. 

 

 

Failure to use personal protective equipment could result in serious injury or death. 

 

 

 

8.14. 

Warning Decals:

 

Check monthly to verify that all the warning decals are in position and 

legible. See Section 0.0 for full descriptions and locations. 

 

 

Failure to maintain warning decals risks the possibility of not alerting the abrasive blaster 

operator to potential dangers which can result in serious injury or death. See Section 0.0. 

 

 

8.15. 

Handway Assembly:

 Refer to Section 6.3 for installation and inspection procedures. 

 

 

8.16. 

Moisture Separator and Strainer:

  With the air supply on, once a day completely open the 

moisture separator drain ball valve (#8) and the control air strainer petcock (#23) to purge all 

moisture and debris. Purge for about one minute then close the ball valve and petcock. 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание MV3
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды