Schmidt MV3 Скачать руководство пользователя страница 33

Страница: 33 / 79

5.13 Union End Ball Valve (optional)

The union ball valve is used to block the abrasive flow to the MV3 Valve. This allows the user

to remove the MV3 Valve from the blast vessel without emptying the abrasive. Turn the union

ball valve handle to the horizontal position to block abrasive flow. Loosen the nut to separate

the two sections of the union ball valve and remove the MV3 Valve from blast vessel. The

handle on the union ball valve can be difficult to turn; however, there are punched holes at each

arm of the handle where a standard ratchet wrench can be inserted and used as leverage to open

or close the valve.

Note:

Units manufactured after February 2015 are equipped with the

ergonomic round handle design (see Figure 5.7).

The Abrasive blaster is a Pressurized Vessel. Propelled objects will cause serious injury or

death. Depressurize vessel before performing any maintenance. See Section 6.2.

Note:

The union end ball valve is optional and can be added to any blaster; however, some

models may require extensions below the legs for field addition. Consult Axxiom

Manufacturing or an Authorized Schmidt® distributor.

Figure 5.7 – Union End Ball Valve

5.14 Thompson® Valve / Tera Valve® Conversion

The MV3 Valve abrasive blaster is best suited for large blast projects where the operator will

blast for long periods without repeated starts and stops. Because the MV3 blaster is a

depressurized

blast system all the air pressure in the blast vessel is vented each time the

deadman lever is released. When blasting is restarted differential pressure occurs at the MV3

valve until the blast vessel reaches full pressure. This differential pressure causes momentary

wear in the MV3 and does so each time the blaster is restarted. Therefore, for blast applications

that are short blast times and frequent start and stops it is recommended to use a pressurized

Thompson® Valve or Tera Valve blast system to minimize wear caused by differential

pressure. Conversion kits are available to convert MV3 blasters to Thompson Valve or Tera

Valve controls.

Note:

Thompson Valve conversion requires additional clearance below the

blaster; however, Tera Valve conversions do not. Consult Axxiom Manufacturing or an

Authorized Schmidt® distributor.

5.15 Dual Outlet Blast System (10cf and 20cf)

The 10cf and 20cf blast vessels are fabricated with two additional abrasive outlet couplings.

These vessels can be purchased as dual outlet or field converted to dual outlet blasters. Consult

Axxiom Manufacturing or an Authorized Schmidt® distributor.

Содержание MV3




























































Результаты поиска

Содержание MV3

Отзывы:

Бренды по названию

Популярные бренды

Schmidt MV3, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MV3

Отзывы:

Бренды по названию

Популярные бренды