Schmidt MV3 Скачать руководство пользователя страница 43

Страница: 43 / 79

7.2 Beginning the Blasting Operation (See Figure 7.1 or 7.2)

7.2.1. The abrasive blaster must be properly setup and all operating personnel must be

thoroughly trained before beginning the blast operation. All operators must completely

read and understand all sections of this manual before beginning the blast operation. See

the pre-operation setup procedures given in Section 6.0.

7.2.2. Perform the required inspections and maintenance before beginning the blast operation.

See the instructions given in Section 8.0.

The abrasive blaster is a Pressurized Vessel. Propelled objects will cause serious injury

or death. Depressurize vessel before performing any maintenance. See Section 6.2.

7.2.3. Open the abrasive shutoff valve (optional, see Section 5.13).

7.2.4.

Open the choke valve (#13). Always leave the choke valve completely open while

blasting. Close the choke valve only for the “choke” procedure (see Section 11.3.2.). Do

Not blast for long periods with the choke valve partially closed since this will cause

excessive wear in the MV3 Valve (#14).

7.2.5.

For initial startup, the MV3 Valve (#14) should only be partially open. Turn the valve

knob clockwise to completely close, then turn counterclockwise about four turns to

partially open. The best setting for the valve varies depending on abrasive type, blast

pressure, and nozzle size; therefore, it may take more than one adjustment to achieve the

desired air/abrasive mixture. Further adjustment can be made later as needed.

7.2.6. Slowly open the inlet ball valve (#3). This will supply air to the ComboValve® (#4) and

the deadman controls (#12 & #15). The blast vessel will not pressurize.

7.2.7. Slightly open the ball valve (#8) on bottom of the moisture trap (#7) to permit moisture

to continually drain during the blast operation (optional, see Section 5.4). Once each day

completely open the drain ball valve to blow out all moisture and dirt particles.

7.2.8. The following steps are for abrasive flow setting which may require several adjustments

and testing of the blast flow. It is recommended that testing of the blast be made on a

test piece so not to damage anything of value.

7.2.9.

With one hand grip the blast hose assembly (#10) and with the other hand press in the

deadman safety button.

To begin blasting, aim the blast nozzle at the object to be

blasted, then firmly press down the deadman lever (#12). The ComboValve® will open

and pressurize the abrasive blaster. Air and blast abrasive will flow into the blast hose

and out through the blast nozzle (#11).

Do Not aim the blast nozzle towards yourself or any person. A system malfunction or a

blocked blast nozzle that clears can trigger accidental start up resulting in injury to

personnel.

7.2.10. Observe the blast stream and the coating removal rate. A bluish color in the blast stream

indicates a good abrasive to air mixture. Release the deadman lever to stop blasting

Содержание MV3




























































Результаты поиска

Содержание MV3

Отзывы:

Бренды по названию

Популярные бренды

Schmidt MV3, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание MV3

Отзывы:

Бренды по названию

Популярные бренды