manualshive.com logo in svg

Schmidt MV3, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Schmidt MV3 Скачать руководство пользователя страница 27

  

 

27 

Copyright © 2021 Axxiom Manufacturing, Inc. 

 

 

See Figure 5.1  below  or Figure 9.2(a) to help understand  the  general  operation  of a MV3  abrasive 

blaster. Do not attempt to operate the abrasive blaster before reading all sections of this manual and 

following all setup procedures.  Read Sections 5.1 through 5.17  for a detailed explanation of all 

components of the MV3 abrasive blaster. 

 

The MV3 abrasive blaster is a 

depressurized system

; meaning the blaster will pressurize only when the 

ComboValve® is opened by pressing the deadman lever (#12). 

 

Compressed air enters the blast system when the air inlet ball valve (#3) is opened. Air flows through 

the moisture separator (#7) and into the supply side of ComboValve  (#4). Air is supplied to the 

deadman valve (#12) from the ComboValve. When the deadman lever (#12) is pressed down signal air 

will flow back to open  the  ComboValve. When the ComboValve  opens air will  flow into the blast 

vessel internal piping. The air flow pushes the popup (#5) against the gasket (#6) to seal the abrasive 

inlet and allow the air flow to pressurize the blast vessel (#1) and the blaster piping (#13). 

 

Blasting starts when the deadman lever (#12) is pressed  down.  Compressed air will  flow from the 

ComboValve (#4) to the blast hose (#10).  The choke ball valve (#13) must be open during the blast 

operation.  Abrasive will flow through the MV3  Valve  (#14)  and  fall  into the blast  air stream. The 

abrasive flow can be increased or decreased by turning the knob on top of the MV3  Valve  (#14). 

Because of the length of the blast hose, it will take a few seconds to see changes in abrasive flow. 

 

Blasting stops when the deadman lever (#12) is released. This will close  the ComboValve (#4) and 

depressurize the vessel at the same time.  The compressed air in the abrasive blaster will exhaust 

through the blowdown hose (#9) and through the VBS Suppression System (#45). The MV3 abrasive 

blaster (#1) remains depressurized when the ComboValve (#4) is closed. 

 

 

Figure 5.1 – MV3 Abrasive Blaster with pneumatic blast controls 

5.0  MV3 Abrasive Blaster General Operation 

 

Содержание MV3
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды