manualshive.com logo in svg

Schmalz SCPi FS RP, Руководство по эксплуатации

Поделиться
Скачать
Schmalz SCPi FS RP Скачать руководство пользователя страница 26

Installation

26 / 58

EN-US · 30.30.01.01602 · 01 · 10/18

7   Installation

7.1   Installation Instructions

 CAUTION

Improper installation or maintenance

Personal injury or damage to property

4

During installation and maintenance, make sure that the ejector is disconnected and
depressurized and that it cannot be switched on again without authorization.

For safe installation, the following instructions must be observed:

1. Use only the connections, mounting holes and attachment materials that have been provided.

2. Carry out mounting and removal only when the device is in an idle, depressurized state.

3. Pneumatic and electrical line connections must be securely connected and attached to the ejector.

7.2   Installation

The ejector may be installed in any position.

When installing the ejector, make sure that the areas around the silencer and the bypass remain free, so
that unimpeded discharge of the escaping air is ensured.

Bypass

Silencer

Four mounting holes for 2x M5 and 2x M6 screws are used to fix the ejector. The ejector is to be fixed
with at least 2 screws, the maximum tightening torque is 6 Nm.

Mounting hole 2xM5

Mounting hole 2xM6

Содержание SCPi FS RP



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды