background image

 SCHLAGEL, INC.

 SCHLAGEL, INC.

                                                             EDI - V5 CONTROL

 

 

 

Page 10 

EDIT DUCT NUMBER 01 
                     
ENTER F-KEY NBR <1> 

               ->

   

 

Changing the Line 1 caption is a good example of using the special access codes 
and character programming so we will explain all of the details here. 
 

At the O

PERATING

 screen press 8004 

Enter

. That is the access code for changing 

the caption. The blinking cursor shows where each character will be entered. 

Pressing any numeric key will enter that number and move the cursor right to the 

next position. 

The 

Shift

 key is used to enter an alpha character. Consider the number 

key. On 

the top left of the key is the character 

and at the top right is the character 

B

. To 

enter an 

A

 press the 

Shift

 key once and a ‘

-‘ 

will appear under the cursor. Now 

press the 

7

 key and the 

A

 character will be entered. If the 

Shift

 had been pressed 

twice, a “

=

” would have been shown and after pressing the 

7

 key, a 

B

 would have 

been entered. Pressing the 

Shift

 key multiple times changes the cursor background 

between “ “, “-“, “=”, and back to “ “. 

Up to 16 characters may be entered. A space is entered with a single 

Shift

 and 

Space.

 A backspace can be executed by a double 

Shift

 and 

Space

. When finished, 

press the 

Enter

 key. The display will return to the O

PERATING

 screen showing the 

new caption. Changing the caption is a good way to build your editing skills 
without affecting the operation of the distributor. 

 
 

 

Note: 

To modify duct information, the spout must first be set to the position you 

intend to modify. 
 
At the O

PERATING

 screen press 5993 

Enter

. This displays the first prompt screen 

(see below) requesting the access number. This can be any number, 1 thru 255, and 

will be the number used to move the spout to this duct from the O

PERATING

 screen. 

After entering the access number press 

Enter

 
 
 
 
 
 
 
The next prompt screen asks for the 

F-KEY

 number. There are 6 ‘speed-dial’ keys 

on the keypad that can be used for frequently accessed positions. Here is where you 
can specify the assignment of a function key for this position by entering a number, 
1 thru 6. Enter a 0 (zero) if no function key will be assigned to this position. When 
finished, press 

Enter

 
 
 
 
 
 
 

Modify Line 1 
(Access code 8004) 

 
Modify Line 3 
(Access code 5993) 
 

 EDIT DUCT NUMBER 01 
                     
ACCESS NUMBER <001> 

             ->

   

Содержание EDI-V5 CONTROL

















Отзывы: