3 • Schlage • WRI400 user guide
Overview
The Schlage Wireless Reader Interface (WRI400) is an open architecture Wireless Access
Point Module (WAPM) designed to interface with third-party panels through a Panel Interface
Module (PIM400-TD2, PIM400-485) by using radio frequency (RF) communication.
• Interfaces credential readers and portal access control with third-party panels.
• May be used with up to two (2) credential readers that use wiegand or clock and data
outputs.
•
Supports five (5) optional inputs: Reader 1 Tamper and Reader 2 Tamper, Request to
Enter, Request to Exit and Door Position (Portal Status).
• Supports two (2) Form C, dry contact relays intended for strike and auxiliary outputs
(i.e., door installations with magnetic locks or strikes).
• Externally powered using a UL294 for UL, and ULCS318/ULCS319 for cUL listed Class
2 power supply (not included) capable of sourcing at least 500 mA @ 12 or 24 VDC,
(example: Schlage models PS902, PS904, PS906).
• Suitable for outdoor use, ambient temperature range -35C to +66C (-31F to +151F).
• The WRI400 is listed under UL294 as an access control system accessory.
• Access equipment manufactured and/or sold by Allegion LLC, is not rated for, or
intended for use in life safety installations. UL listed panic hardware must be used to
allow emergency exit from the protected area.
• The WRI400 has not been evaluated to UL325 or UL508.
• The ANT400 antennas have not been evaluated to UL294 and are not for use in
UL installations.
• This product has been evaluated for ULC-S319 Class I.
+
-
+
-
C
B+
1
+
+
1
1
GND
GND
IF RADIO BOARD PRESENT
NC
BATT
COIN CELL NOT NEEDED
NC
C
NO
C
NO
PRIMARY SIDE
BEEPER
BEEPER
ALARM
STRIKE
AUX
PWR/
SIDE UP
LINE
GND
RT
E
GND
GND
1
1
1
1
RED
GRN
GND
DA
TA\D0
CLK\D1
GND
SWITCH INPUT
CLK\D1
DA
TA\D0
RED
GRN
READER1
READER2
TAMP2
TAMP1
DPS
RT
X
GND
DEBUG
TAMPER
STATUS
RELAY
RX/TX
USB
+12V
+5V
LID
+3.3V
RX
TX
GND
OPEN
A-
1
1
1
1
1
1
1
1
23394075_C
SCHLAGE
LINK
RESET
TAMPER
GND
20
19
2
1
ICLK
IDAT
RB8
RB7
GND
VDD
MCLR
USB
AA
BATT
LINE
ALR_NC
ALR_C
ALR_NO
AUX
AUX
AUX
STR
STR
STR
RB+
TB+
TA
-
RS485
12/24VDC
THIS
MOUNT
LED2
BATTERY_HOLDER1
R1
12 C61
U4
REL1
J3
J7
REL2
REL3
U5
TP25
TP24
TP23
TP22
TP21
J6
LED1
LED4
LED7
LED5
LED6
LED3
J18
J17
J13
LED8 LED9
C32
J9
J12
J11
J10
J8
S3
S2
S1
J5
J2
J1
J2
Lid Tamper
Input Switch
J13
Switch Inputs
J10
Reserved
J5
USB
J7
Power
12 or 24
VDC
J17
Reader 1
J18
Reader 2
J6
Relay Outputs
Radio Board
SW1
Lid Tamper
Switch
