manualshive.com logo in svg

Schlage WRI400, Инструкция по эксплуатации

Поделиться
Скачать
Schlage WRI400 Скачать руководство пользователя страница 15

15  •  Schlage  •  WRI400 user guide

Credential readers

An input device with either Wiegand (Data1/Data0) or magnetic (clock and data) bit stream 

can be used with the WRI400. The WRI400 provides two separate credential reader 

interfaces.
Connect the shield of the Reader 1 cable to the WRI400 J17-3 terminal (GND). Connect the 

shield of the Reader 2 cable to the WRI400 J18-3 terminal (GND). Do not connect the cable 

shield at the credential reader.

 

L

Reader input ports are designed for 5V logic. Any voltage greater than 5V may 

cause damage to either the WRI400 or the readers.

The WRI400 does not provide power to the readers. Power must be provided to the 

readers separately by a UL listed power supply.
The WRI400 may not provide complete control of the reader’s beeper or LEDs. Please 

consult with your reader’s manufacturer for instruction on reader configuration.

Reader 1 

terminal

Reader 2 

terminal

Description

CLK/D1

J17-1

J18-1

Credential reader inputs: Each input line is pulled to GND 

through a 12V transient suppressor and a 2 mega-ohm 

resistor.
Wiegand or magnetic format is automatically detected.

DATA/D0 J17-2

J18-2

GND

J17-3

J18-3

The signal ground of the WRI400 must be tied to the 

signal ground at the reader.

BEEPER J17-4

J18-4

Beeper signal line connection to the reader.
This is an “open collector” style output and has a 12V 

transient suppressor to GND.
The output is switched to GND through a 100 Ohm 

resistor to activate the beeper on the reader.
NOTE: Most readers beep independently, and beeper 

performance depends on the specific reader model.

GRN

J17-5

J18-5

Green LED signal line connection to the reader.
This is an “open collector” style output and has a 12V 

transient suppressor to GND.
The output is switched to GND through a 100 Ohm 

resistor to activate the green LED on the reader.

RED

J17-6

J18-6

Red LED signal line connection to the reader.
This is an “open collector” style output and has a 12V 

transient suppressor to GND.
The output is switched to GND through a 100 Ohm 

resistor to activate the red LED on the reader.

Содержание WRI400

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды