Schlage KC9232 Скачать руководство пользователя

Страница: 3 / 20

KC9232/KC9232-2 & KC9233/KC9233-2 INSTALLATION

Introduction / Tools and Materials Needed / Contact Info

57041-D Page 3 04-11-2007

Introduction / Tools and Materials Needed / Contact Info

Introduction:

The KC9232/KC9232-2 and KC9233/KC9233-2 are designed to replace existing

exterior cylinders or trim on Adams Rite® deadlatches. The trim will retract the

deadbolt or latch when an access code or iButton is entered and the knob is turned.

Mechanical key override is standard. The trim is compatible with interior devices

such as a thumbturn or mortise cylinder. Adams Rite® deadbolt accessories 4015

threshold bolt and 4016 header bolt are also compatible with these models of the

KC9000 series trim. With existing or new Adams Rite® trim on the inside the

‘hold back’ feature is still possible for a continued unlatched function (see Adams

Rite® instructions where applicable). An Audit Trail feature is available on the

KC9232-2 and the KC9233-2 models.

The KC9232/KC9232-2 (trim w/knob & MS Cam interface) is compatible

with Adams Rite

MS1850, MS1850-050, MS1950, 4070 Deadbolts, 4710

Deadlatch locks and 8400 mortise exit devices.

The KC9233/KC9233-2 (trim w/knob and 4070 Cam interface) is compatible

with Adams Rite

4070 Short Throw Deadbolt.

Tools and Materials Needed:

Contact Information:

Schlage Lock Company

575 Birch Street

Forestville, CT 06010

technical support: 866-322-1237

fax: 866-322-1233

web: http://www.irsupport.net

1. Flat head screwdriver w/straight, 1/8” wide blade.

2. Small Philips head screwdriver

3. 3/32” Allen wrench

4. 1/16” Allen wrench

5. Center punch

6. Hammer

7. Pencil

8. Drill & Tap for 10-32 threads

Содержание KC9232





















Результаты поиска

Содержание KC9232

Отзывы:

Похожие инструкции для KC9232

Бренды по названию

Популярные бренды

Schlage KC9232, Руководство по установке

Результаты поиска

Содержание KC9232

Отзывы:

Похожие инструкции для KC9232

Бренды по названию

Популярные бренды