Schiller Grounds Care Bob-Cat 942311F Скачать руководство пользователя страница 11

Страница: 11 / 70

FastCat RZ

SET UP INSTRUCTIONS

TOOLS REqUIRED FOR ASSEMBLY

Wrecking bar

Claw hammer

Sockets: 1/2”, 15/16

Wrenches: 18mm, 1/2”, 9/16”, 3/4”, 15/16”

Tire pressure gauge

NOTE:

All references below to the “right” or “left” are with respect to an operator at the controls.

UNCRATE UNIT

a) Discard packing materials. Loosen the caster wheel axle bolts and bumper bolts to remove the shipping

brackets.

Discard shipping brackets.

b) Re-install and tighten bumper bolts.

c) Tighten caster wheel axle bolts against caster axle spanner bushings to 80 ft/lbs.

TIRE PRESSURE

a) Set tire pressures to 14 lbs/in

(1.0 kg/cm

). Tires are overinflated for shipping.

TRACTION LEVERS

a) Tighten bolt

b) Sit on the machine. Levers

may be moved to

upper set of holes in bar

for a better operator

fit.

Содержание Bob-Cat 942311F







































































Результаты поиска

Содержание Bob-Cat 942311F

Отзывы:

Похожие инструкции для Bob-Cat 942311F

Бренды по названию

Популярные бренды

Schiller Grounds Care Bob-Cat 942311F, Руководство оператора

Результаты поиска

Содержание Bob-Cat 942311F

Отзывы:

Похожие инструкции для Bob-Cat 942311F

Бренды по названию

Популярные бренды