Schiller Grounds Care Bob-Cat 942311F Скачать руководство пользователя страница 17

Страница: 17 / 70

FastCat RZ

At operator's right side

KEYSWITCH (K)

The keyswitch has three

positions:

OFF

RUN

, and

START

. Insert the key

and turn it clockwise to move the switch from

OFF

RUN

. Turn it further to

START

and hold to engage

the starter. Release the key and the switch will return
to

RUN

from

START

. Turn the key counterclockwise

OFF

to stop the engine.

THROTTLE (T)

Move the throttle lever forward to

increase engine speed until the maximum governed
engine

RPM

is reached. Move the lever rearward to

decrease engine speed until the engine reaches its
idle speed.

CHOKE (C)

Pull the choke control out to set the choke

. Push

it in to set the choke

OFF

POWER TAKE OFF (PTO) SWITCH

(P)

The operator must be in the seat when engaging the

PTO

or the engine will kill. Pulling the

PTO

switch

out engages (turns on) the

PTO

and starts the blades

or other attachment. Pushing the

PTO

switch in

disengages (turns off) the

PTO

and stops the blades

or other attachment.

NOTE:

The

PTO

switch does not control

attachments powered by a separate engine.

Disengage the

PTO

whenever you stop or leave

the operator’s position

Shut off engine with the key and remove the
spark plug wires before making adjustments or
unplugging a clogged mower.

Do not engage the

PTO

until ready to start

mowing.

CONTROLS

Содержание Bob-Cat 942311F







































































Результаты поиска

Содержание Bob-Cat 942311F

Отзывы:

Похожие инструкции для Bob-Cat 942311F

Бренды по названию

Популярные бренды

Schiller Grounds Care Bob-Cat 942311F, Руководство оператора

Результаты поиска

Содержание Bob-Cat 942311F

Отзывы:

Похожие инструкции для Bob-Cat 942311F

Бренды по названию

Популярные бренды