Schiller Grounds Care Bob-Cat 942311F Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 70

background image

27

FastCat RZ

SPARK PLUGS

Remove each plug and check condition.

-

Good operating conditions are indicated if the plug has a light coating of grey or tan deposit.

-

A white blistered coating indicates overheating. A black coating indicates an “over rich” fuel mixture. Both
may be caused by a clogged air cleaner or improper carburetor adjustment.

-

Do not sandblast, wire brush or otherwise attempt to repair a plug in poor condition. Best results are
obtained with a new plug.

- Set plug gap as specified in engine manual..

MAINTENANCE

FUEL FILTER

An in-line fuel filter is located in the fuel supply line. Inspect at every oil change to make sure it is clean and

unobstructed. Replace if dirty.

ENGINE OIL

Do not perform engine maintenance without the
engine off, spark plug wires disconnected and PTO
disengaged.

AFTER FIRST FIVE (5) HOURS

While the engine is warm:

1. Release the oil drain hose assembly from the

engine clip

J

. Lay hose assembly over the frame

edge or through the frame cutout, which ever is
most convenient.

2. Remove the rubber cap

D

from the tip of the

hose assembly and turn the drain valve to allow
oil to drain from the engine. Dispose of used oil
in accordance with local requirements.

3. Clean drain valve and tighten the plastic portion

of the drain valve back into the metal portion of
the valve. Replace rubber cap over the tip of the
valve. Replace hose assembly back into engine
clip.

4. Change oil filter.

5. Fill the crankcase with fresh oil to the full mark.

Do not overfill. See engine manual for oil

specifications.

DAILY

1. Check oil level with the dipstick.
2. If oil is needed, add fresh oil of proper

viscosity and grade. See engine manual for oil

specifications. Do not overfill.

3. Replace dipstick before starting engine.

PERIODIC OIL CHANGES

1. See engine manual for oil and filter change inter

-

vals after the break-in period.

2. Follow instructions for first oil change, above.

«
...
27
28
29
30
31
...
»

Содержание Bob-Cat 942311F







































































Отзывы:

Нет отзывов

Похожие инструкции для Bob-Cat 942311F

Бренд: Sears Страницы: 37

Бренд: FERRI Страницы: 139

Craftsman EZ3 917.259553

Бренд: Sears Страницы: 56

Бренд: Dixon Страницы: 48

Бренд: Powerplus Страницы: 18

Бренд: Lastec Страницы: 21

36V UltraStore 340R

Бренд: Flymo Страницы: 14

Zero Turn Radius Mower

Бренд: Country Clipper Страницы: 25

Бренд: Dolmar Страницы: 224

Бренд: Lastec Страницы: 54

Бренд: Country Clipper Страницы: 28

Бренд: Bad Boy Страницы: 48

Бренд: Parkside Страницы: 52

LX420 13AX60RG744

Бренд: Toro Страницы: 36

Timing Deck Striper/Roller

Бренд: Cub Cadet Страницы: 8

TOURNO compact 115

Бренд: Cramer Страницы: 26

Бренд: Kubota Страницы: 117

Бренд: Cub Cadet Страницы: 867

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды