background image

16.

        WARNING!  People with pacemakers should consult their physician(s)
before using this product.  Operation of electrical equipment in close proximity to
a heart pacemaker could cause interference or failure of the pacemaker.

17.

        WARNING!  The warnings and cautions discussed in this manual cannot
cover all possible conditions and situations that may occur.  It must be understood
by the operator that common sense and caution are factors which cannot be built
into this product, but must be supplied by the operator.

SAVE THESE  INSTRUCTIONS

and other construction activities, contain chemicals known 

to cause cancer, birth

defects or other reproductive harm.  Some

 examples of these chemicals are:

lead from lead-based paints, crystalline silica

 from bricks and cement or other 

masonry products, arsenic and chromium from

 chemically treated lumber.  

Your risk from these exposures varies, depending on

 how often you do this type of 

work.  To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock.
Check with a qualified electrician if you are in doubt as to whether the outlet is
properly grounded.  Do not modify the power cord plug provided with the tool.
Never remove the grounding prong from the plug.  Do not use the tool if the power
cord or plug is damaged.  If damaged,  have it repaired by a service facility before
use.  If the plug will not fit the outlet, have a proper outlet installed by a qualified
electrician.

        PAGE 6

Содержание TIGER2000S


















Отзывы: