18 І 80
www.scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
www.scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
The device is not suitable for grinding serrated knives.
Sharpening scissors (Fig. E)
1. Mount the selected sharpener (see Mounting
sharpener).
2. Completely open the scissors.
3. Insert the scissor blades into the scissor
sharpening slot.
4. Using light pressure guide the blade from the screw
up to the tip along the grinding wheel (10).
5. Remove the scissors from the sharpening station
and turn the scissors to sharpen the other blade.
6. Insert the other scissor blade into the scissor
sharpening slot.
7. Using light pressure guide the blade from the screw
up to the tip along the grinding wheel (10).
8. Execute the alternating grinding process until the
cutting edges are burr-free and sharp.
9. Switch the device off and wait for the grinding
wheel (10) to stop.
The device is not suitable for grinding serrated scissors.
The device is not suitable for grinding pinking shears.
Change grinding disc
Information on replacement:
•
Never operate the device without protective
equipment.
•
Ensure that the grinding disc dimensions match those
of the device.
•
Never use separate bushings or adapters in order to
make grinding discs whose hole is too large fit the
device.
•
Do not use any saw blades.
•
Always reassemble the device completely after
replacing the grinding disc.
Switch the device off and remove the mains plug. Allow
the device to cool down.
When the grinding disc nut (16) is being tightened or
loosened, the axle has to be held firmly in place with a
pair of pliers or the grinding disc (10) held firm by hand.
1. Release the grinding wheel nut (16) in the
clockwise direction (left-handed thread).
2. Remove the grinding wheel (10).
3. Set up a new grinding wheel (10). Screw the
grinding wheel nut (16) in the anti- clockwise
direction (left-handed thread).
4. Test run: Before starting work and after each
change of grinding disk, carry out a test run of
at least 60 seconds with no load. Switch off the
equipment immediately if the disk runs lumpy,
substantial vibrations occur, or abnormal noises are
generated.
Transport
1. Turn off the power tool before any transport and
disconnect it from the power supply.
2. Protect the power tool from knocks, bumps and
strong vibrations, such as during transport in vehi-
cles.
3. Never use the safety devices for handling or trans-
porting purposes.
3. Insert the drill into the drill holder (14).
4. Insert the drill holder (14) into the adjusting device
(15).
5. Push the drill to the front into the V-nut up to the
metal stop. The cutting edges of the drill must fit
closely to the metal surfaces.
6. Using the knurled nut fasten the drill for drill-
fastening (12).
7. Remove the drill holder (14) and insert it into the
rotatable drill mount (11).
8. Check the alignment of the drill. The cutting edges
of the drill must be touching the grinding wheel
(10).
9. Switch the device off and grind the drill.
10. Switch the device off and wait for the grinding
wheel (10) to stop.
11. Remove the drill holder (14) and insert it into the
rotatable drill mount (11) by rotating in by 180°.
Using the same adjustment, you can grind the
opposite cutting edge of the drill.
12. Switch the device off and grind the drill.
13. Switch the device off and wait for the grinding
wheel (10) to stop.
Sharpening picks and chisels (Fig. C)
1. Mount the selected sharpener (see Mounting
sharpener).
2. Place the blade on the tool table (6) so that the end
to be sharpened fits closely to the edge of the tool
table (6). The magnetic holder (5) keeps the blade
in position.
3. For small picks, use the spacer (4).
4. Select the angle according to the existing bevel
angle (angle of the bevelled edge).
5. Release the retaining screw for the angular
adjustment (7) and turn the tool table (6) into
position.
6. Tighten the retaining screw for angular adjustment
(7) again.
7. Switch the device on and move the tool table (6)
equally back and forth along the grinding wheel
(10).
8. Always use light pressure while sharpening and
slowly push the blade towards the grinding wheel
(10).
9. Repeat the sharpening process until all
irregularities have been removed.
10. Switch the device off and wait for the grinding
wheel (10) to stop.
Sharpening knives (Fig. D)
1. Mount the selected sharpener (see Mounting
sharpener).
2. Insert the blade of the knife right into the knife
sharpening slot.
3. Using light pressing guide the blade along the
grinding wheel (10) and evenly and slowly pull the
knife towards you.
4. Turn the knife and insert the knife blade into the
opposite knife sharpening slot.
5. Repeat this grinding process for this side of the
blade as well.
6. Execute the alternating grinding process until the
cutting edge is burr-free and sharp.
7. Switch the device off and wait for the grinding
wheel (10) to stop.
Содержание GS650
