Scheppach 5906135901, Перевод с оригинального руководства пользователя

Страница: 21 / 104


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
GB
| 21
• Avoid long air lines and supply lines (extension
cables).
• Make sure that the intake air is dry and dust free.
• Do not install the compressor in a damp or wet
room.
• The compressor may only be used in suitable
rooms (with good ventilation and an ambient tem -
perature from +5 °C to 40 °C). There must be no
dust, acids, vapors, explosive gases or inflamma -
ble gases in the room.
• The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor in
areas where work is conducted with sprayed water.
8. Attachment and operation
n
Important!
You must fully assemble the appliance before
using it for the first time!
You will require the following tools for assembly
and installation: 1x Screwdriver an 1x open-ended
wrench size 13 mm (not included)
8.1 Fitting the wheels (9)
• Fit the supplied wheels (9) as shown in fig. 4.
8.2 Fitting the supporting foot (A)
• Fit the supplied supporting foot (A) as shown in
fig. 5.
8.3 Installation of the air filter (13)
• Remove the transport plug (fig. 10 pos. F) and at -
tach the air filter (fig. 11 pos. 13) on the unit by turn -
ing clockwise (N) (fig. 12).
• Solve for maintenance the air filter (13) by turning
counter-clockwise (M) (Fig. 12).
8.4 Changing the transportation cover
(Figure 7 - 9)
Remove the transport lid (12) of the oil filling opening .
Fill the included compressor oil into the crank hous -
ing and insert the included oil sealing plug into the oil
filling opening.
Checking the oil level (Figure 7 - 9)
m
Warning: For the first use, check the oil level of
the compressor.
1 Operating the machine without oil will cause irrep -
arable damage and render the warranty invalid.
2 Remove the plastic oil inlet plug on top of the
crank box of the compressor casing. (see fig. 7)
3 Check the oil level in the sight glass (fig. 9 pos. 17).
The oil level should be in the centre of the red cir -
cle. (see fig. 9 pos. 17.1)
4 Attach the closing plug (fig. 8 pos. 12), which is
included and pull it tight.
Operating pressure vessels
• You must keep your pressure vessel in good work -
ing order, operate the vessel correctly, monitor the
vessel, carry out necessary maintenance and re -
pair work immediately and meet the relevant safety
precautions.
• The supervisory authority may enforce essential
control measures in individual cases.
• A pressure vessel is not allowed to be used if it has
faults or deficiencies that can endanger workers
or third parties.
• Check the pressure vessel for signs of rust and
damage each time before using. Do not use the
compressor with a damaged or rusty pressure
vessel. If you discover any damage, then please
contact the customer service workshop.
Do not lose these safety instructions
6. Technical data
Mains connection 230 V~ 50 Hz
Motor rating max. 1500 W
Operating mode S1
Compressor speed 2850 min
-1
Pressure vessel capacity approx. 24 l
Operating pressure approx. 8 bar
Theoretical intake capacity approx. 220 l/min
Sound power level L
WA
93 dB(A)
Uncertainty K
WA
2.4 dB
Protection type IP20
Weight of the unit 21 kg
The noise emission values were measured in ac -
cordance with EN ISO 2151.
Wear hearing protection.
The effects of noise can cause a loss of hearing.
7. Before starting the equipment
Before you connect the equipment to the mains sup -
ply make sure that the data on the rating plate are
identical to the mains data.
• Prior to initial commissioning, remove the trans -
port plug (12) and fill the crank housing with oil as
described in 8.4.
• Check the equipment for damage which may have
occurred in transit. Report any damage immedi -
ately to the transport company which was used to
deliver the compressor.
• Install the compressor near the point of consump -
tion.