www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 81
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
10. Cleaning, maintenance, storage
and transport
m
Important!
Pull out the power plug before doing any clean-
ing and maintenance work on the equipment.
Risk of injury from electric shock!
m
Important!
Wait until the equipment has cooled down complete-
ly! Risk of burns!
m
Important!
Always depressurize the equipment before carry-
ing out any cleaning and maintenance work! Risk
of injury!
10.1 Cleaning
• Keep the equipment free of dirt and dust as far as
possible. Wipe the equipment with a clean cloth or
blow it down with compressed air at low pressure.
• We recommend that you clean the equipment im-
mediately after you use it.
• Clean the equipment regularly with a damp cloth
and some soft soap. Do not use cleaning agents
or solvents; these may be aggressive to the plastic
parts in the equipment. Ensure that no water can
get into the interior of the equipment.
• You must disconnect the hose and any spraying
tools from the compressor before cleaning. Do not
clean the compressor with water, solvents or the
like.
10.2 Maintenance of the pressure vessel (fig. 1)
m
Important!
To ensure a long service life for the
pressure vessel (2), drain off the condensate after
each use by opening the drain screw (1). Release
the vessel pressure at the overpressure valve (17)
beforehand. The drain screw is opened by turning it
counter-clockwise (when looking at the screw on the
bottom of the compressor) so that the condensate
can be completely drained out of the pressure ves-
sel. Then close the drain screw again (turn clock-
wise). Check the pressure vessel for rust and dam-
age each time before use.
The compressor shall not be operated if the pressure
vessel is damaged or rusty.
If you discover damage, please contact the customer
service workshop.
8.6 Using the air blow gun
You can also use the air blow gun (12) to clean out
cavities and to clean soiled surfaces and work equip-
ment.
Always wear protective goggles when doing so!
8.7 Using the adapter set
The adapter set enables you to use the following ad-
ditional capabilities of the tyre inflation device:
Pumping up balls with the help of the ball needle (9).
The valve adapter (10) enables bicycle tyres to be
inflated.
Filling pools, air mattresses or boats with the help of
the additional adapter (11).
9. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions. The
customer‘s mains connection as well as the ex-
tension cable used must also comply with these
regulations.
Damaged electrical connection cable
The insulation on electrical connection cables is of-
ten damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been im-
properly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not
be used and are life-threatening due to the insula-
tion damage.
Check the electrical connection cables for damage
regularly.
Make sure that the connection cable does not hang
on the power network during the inspection.
Electrical connection cables must comply with the
applicable VDE and DIN provisions. Only use con-
nection cables with the marking „H05VV-F“.
The printing of the type designation on the connec-
tion cable is mandatory.
AC motor
• The mains voltage must be 220 - 240 V~
• Extension cables up to 25 m long must have a
cross-section of 1.5 mm
²
.
Connections and repairs of electrical equipment
may
only be carried out by an electrician.
