Scheppach 5903205903, Перевод оригинального руководства пользователя

Страница: 21 / 124

www.scheppach.com
GB | 21
• Keep the packaging until the end of the warranty
period.
• Read through the operating manual completely.
• Only use original spare parts or accessories. Origi-
nal spare parts or accessories can be obtained from
your dealer.
• Check that the data on the type plate matches with
the mains power data.
8. Assembly / Before commissioning
m
ATTENTION!
Always make sure the device is fully assembled
before commissioning!
m
Warning!
Always ensure that the machine is switched off and
disconnected from the power supply before changing
the device settings.
• All covers and safety devices must be properly fit -
ted before switching on the device.
• The grindstone must be able to run freely.
• Before operating the on/off switch, make sure that
the grindstone and honing wheel are correctly
mounted and that the moving parts of the device
function smoothly. Visually inspect both for defects.
• Replace a damaged or worn grindstone.
Installation and setting
Please make sure that your grinding machine stands
upright and stable on a solid surface with sufficient
lighting.
The machine has no front or rear side. Grinding can
take place either with or against the direction of rotation.
Tools required for all assembly / adjustment steps:
• Open-ended spanner 19 mm (not included in the
scope of delivery)
The grindstone is not pre-assembled for packaging
reasons
m
Warning!
Do not connect the device to the power supply until
assembly is complete. Failure to do so may result in
accidental starting and possibly serious injury.
ATTENTION!
Always make sure to remove the transport lock -
ing screw A before comissioning! (fig. 2)
Sound test
Check the grindstone for cracks and perform a sound
test for crack detection.
• The grindstone must be removed from the machine
for the sound test. The grindstone stands upright
on the floor. On a hard floor, use a piece of wood as
a support. The grindstone must be dry.
Noise
The noise values have been determined in accord-
ance with EN 62841.
Sound pressure level L
pA
........................... 63,5 dB(A)
Uncertainty K
pA
.................................................... 3 dB
Sound power level L
WA
............................... 76,5 dB(A)
Uncertainty K
WA
.................................................... 3 dB
m
WARNING
Excessive and frequent exposure to noise can lead to
hearing damage or hearing loss.
- Wear hearing protection
- Take breaks.
Total vibration values (vector sum of three directions)
determined according to EN 62841.
NOTE: The specified noise emission values have
been measured in accordance with a standardised
test procedure and can be used to compare one
power tool with another.
The specified noise emission values can also be used
for an initial estimation of the exposure.
WARNING: The noise emission values can vary from
the specified values during the actual use of the power
tool, depending on the type and the manner in which
the power tool is used, and in particular the type of
workpiece being processed.
Implement measures to protect against noise nuisance.
In doing so, take into account the complete working
process, including the times when the power tool is
working without load or switched off. Suitable meas-
ures include regular maintenance and care of the
power tool and the insertion tools, regular breaks as
well as proper planning of the working process.
7. Unpacking
Danger of choking or suffocating
The packaging material, packaging and transport
safety devices are not children‘s toys. Plastic bags,
foils and small parts can be swallowed and lead to
choking.
- Keep packaging material, packaging and trans-
port safety devices away from children.
• Open the packaging and carefully remove the product.
• Remove the packaging material, packaging and
transport safety devices (if applicable). .
• Check the completeness of the scope of delivery. The
customer service must be notified immediately of any
complaints. Later claims will not be recognised.
• Check the scope of delivery for transport damage.
The transport company must be notified immediately
of any complaints. Later claims will not be recognised.