www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 37
9. Connect the machine stand part 2 (24b) with the
machine stand part 3 (24c) using two Phillips
screws M5 x 40 mm (D) and two nuts M5 (M) on
each side.
(fig. 12)
10.
Fit two flat end caps (N) on the ends of machine
stand part 3 (24c).
11. Connect the machine stand part 3 (24c) with the
machine stand part 6 (24f) using one coach bolt
M8 x 78 mm (A), one spacer (J) and one nut M8
(K) on each side.
(fig. 13)
NOTE: Do not over-tighten the screws. The parts
must be able to move freely.
12. Connect the machine stand part 4 (24d) with the
machine stand part 3 (24c) using one coach bolt
M8 x 78mm (A), one spacer (J) and one nut M8
(K) on each side.
(fig. 14)
13. Now connect both wheels (13) with the machine
stand part 4 (24d) using the wheel screws (P) as
shown in fig. 15.
14. Turn the machine so that it rests on the machine
stand (24).
15. Release the locking latch (14) and fold up the ma-
chine stand until the locking pin engages into the
locking latch (14).
9.2 Removing the table inlay (fig. 16)
1. Set the saw blade (1) to the max. cutting depth,
move to the 0° position and lock in place (see 11.2).
2.
Loosen the fixing screw (4a) by turning it a quarter
turn counterclockwise.
3. Remove the table inlay (4) from the saw table (5).
9.3 Riving knife
m
WARNING
Danger of injury due to unexpected start-up of the
machine
- Remove the mains plug from the socket.
You need to remove the table inlay (4) before you can
install and adjust the riving knife (3).
9.3.1 Insertng and adjusting the riving knife (fig.
17 + 18)
1.
Loosen the fixing screw (3a).
(fig. 17)
2. Push the riving knife (3) into the holder.
NOTE: This step is not necessary if the riving knife
(3) is already inserted.
3. Align the riving knife (3) such that
a) the distance between the saw blade (1) and the
riving knife (3) is max. 5 mm (fig. 18) and
b) the saw blade (1) is parallel to the riving knife (3).
3.
Tighten the fixing screw (3a) again.
9.4 Fitting the table inlay (fig. 16)
1. Place the table inlay (4) in the recess.
2.
Tighten the fixing screw (4a) by turning it a quarter
turn clockwise.
You require the following for assembly:
1x open-ended spanner 10/13 mm (26)
1x ring spanner 10/21 mm (27)
(included in the scope of delivery)
1x Phillips screwdriver
1x Allen key 5 mm
(not included in the scope of delivery)
•
Place all supplied parts on a flat surface.
• Group equal parts.
NOTE:
• If connections are secured with a screw (round-
head or hexagon), hexagon nuts and washers, the
washer must be fitted under the nut.
• Insert screws each from outside to inside. Secure
connections with nuts on the inside.
• Tighten the nuts and screws during assembly only
until they are unable to fall off.
If you tighten the
nuts and screws fully before final assembly, it is not
possible to complete the assembly.
9.1 Fitting the machine stand (fig. 5 - 15)
1. Turn the machine over and place it on a clean sur-
face.
(fig. 5)
2. Fasten the two machine stand parts (24f) on the
machine housing using two Allen screws M6 x 53
mm (B), two large washers (I) and two nuts M6 (L)
each.
(fig. 6)
3. Fit both round end caps (O) on the ends of the
machine stand parts (24f).
(fig. 6)
4.
On the other side, fit both flat end caps (N) on the
ends of the machine stand parts (24f).
(fig. 6)
5. Connect the machine stand part 4 (24d) with the
machine stand part 5 (24e) using two Phillips screws
M5 x 50 mm (C) and two nuts M5 (M).
(fig. 7)
6. Connect the machine stand part 4 (24d) with the
machine stand part 1 (24a) using two coach bolts
M8 x 78 mm (A), two spacers (J) and two nuts M8
(K).
(fig. 8)
NOTE: Do not over-tighten the screws. The parts
must be able to move freely.
NOTE: Make sure that the locking latch (14) on ma-
chine stand part 4 (24d) is on the same side as the
locking pin on machine stand part 1 (24a).
(fig. 9)
7.
Fit two flat end caps (N) on the ends of machine
stand part 4 (24d).
(fig. 9)
8. Connect the machine stand part 4 (24d) with the
machine stand part 6 (24a) using two coach bolts
M8 x 78 mm (A), two spacers (J) and two nuts M8
(K).
(fig. 10 + 11)
NOTE: Do not over-tighten the screws. The parts
must be able to move freely.
NOTE: Make sure that the locking latch (14) is on
the same side as the on/off switch (15).
Содержание 59013209942
Страница 66: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58...
Страница 67: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58...
Страница 68: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58...
Страница 70: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58...
