www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
GB | 35
Cutting chipboard
To prevent the cutting edges from breaking when cut-
ting chipboard, do not set the saw blade higher than 5
mm above the thickness of the workpiece.
After sawing
1.
Switch off the circular table saw first and then the
extraction unit. The saw blade continues to run for
a longer time.
2. Do not remove the cut waste on the saw table until
the saw blade has returned to its rest position.
3. Disconnect the circular table saw from the mains
by pulling the mains plug out of the power outlet.
4. Allow the circular table saw to cool down com-
pletely.
Removing trapped material
m
WARNING! Risk of injury!
Improper handling of the circular table saw may result
in serious injury.
• Switch off the circular table saw immediately and
disconnect the mains plug from the power outlet if
the saw blade is jammed in the workpiece or other
blockages occur.
• Use protective gloves and do not touch the saw
blade with your bare hands.
12. Transport (Fig. 38,39)
1. Turn the power tool off before it is transported and
disconnect it from the power supply.
2. Always carry the electric tool with at least one oth-
er person. Do not carry the machine by the table
extensions, but only lift it by the housing.
3. Protect the power tool against knocks, jolts and
strong vibrations, e.g. when it is transported in
motor vehicles.
4. Secure the power tool against tilting and sliding.
5. Never use the protective devices for handling or
transport.
13. Maintenance
m
Warning
! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
• Keep the safety devices, air vents and motor hous-
ing as free of dust and dirt as possible. Wipe the
device off with a clean cloth or blow it out with com-
pressed air at a low pressure.
• We recommend that you clean the device immedi-
ately after every use.
Cutting narrow Workpieces
Longitudinal cuts of workpieces with a width of less
than 120 mm always have to be cut with the help of
a push stick (17). The push stick is included in the
scope of delivery. Replace a worn or damaged push
immediately.
• Adjust the parallel stop according to the planned
workpiece width.
• Advance the workpiece with both hands, making
sure that you use a push stick (17) as a pushing aid
in the vicinity of the saw blade.
• Always push the workpiece through to the end of
the riving knife.
m
Caution! In the case of short workpieces, the push
stick should be used from the beginning of the cutting
process.
Cutting very narrow Workpieces
For longitudinal cuts of very narrow workpieces with a
width of 30 mm and less, a push block must be used
without fail. There is no push block included in the
scope of delivery! (Available from specialist shops)
Replace a worn push block as soon as possible.
• The parallel stop should be adjusted to the cutting
width of the workpiece.
• Press the workpiece with the push block against
the stop rail and push the workpiece with the push
stick (17) through to the end of the riving knife.
Performing Bevel Cuts (Fig. 36)
• All bevel cuts are made using the parallel stop (14).
• Adjust the saw blade to the desired angle.
• Adjust the parallel stop (14) according to the work-
piece width and height.
• Perform the cut according to the workpiece width
Performing Transverse Cuts (Fig. 37)
• Push the transverse stop (31) into one of the two
grooves (28a/b) of the saw table. Adjust to the de-
sired angle. The left groove (28a) is to be used if
the saw blade (4) also has to be positioned at an
oblique angle. This will prevent your hand and the
transverse stop from coming into contact with the
saw blade guard.
• Use the stop rail.
• Press the workpiece irmly against the transverse
stop (31).
• Switch on the saw.
• Push the transverse stop (31) and workpiece in the
direction of the saw blade in order to perform the
cut.
Caution:
Always hold the guided workpiece irmly and nev-
er the free workpiece which is cut off.
• Always push the transverse stop (31) so far for-
wards until the workpiece is completely cut through.
• Switch the saw off again. Only remove sawing
waste when the saw blade has come to a standstill.
Содержание 5901313904
Страница 7: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 7 39 38 31 30 37 28b 28a...
Страница 53: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 53...
Страница 56: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 56...
Страница 59: ...www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 59...
