www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
24 | GB
16. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic.
Defective components must be disposed of as spe-
cial waste. Ask your dealer or your local council.
Old devices must not be disposed of with house-
hold waste!
This symbol indicates that this product must
not be disposed of together with domestic
waste in compliance with the Directive
(2012/19/EU) pertaining to waste electrical and elec-
tronic equipment (WEEE). This product must be dis-
posed of at a designated collection point. This can
occur, for example, by handing it in at an authorised
collecting point for the recycling of waste electrical
and electronic equipment. Improper handling of
waste equipment may have negative consequences
for the environment and human health due to poten-
tially hazardous substances that are often contained
in electrical and electronic equipment. By properly
disposing of this product, you are also contributing
to the effective use of natural resources.
You can obtain information on collection points for
waste equipment from your municipal administration,
public waste disposal authority, an authorised body
for the disposal of waste electrical and electronic
equipment or your waste disposal company.
When must the oil be changed?
Change the oil after 150 working hours.
Oil change (Fig. 15 - 18)
1. Move the log splitter into the start position and pull
out the mains plug.
2. Undo the oil drain screw with dipstick (8) and put
it to one side. (Fig. 16)
3. Turn the log splitter on the support leg side as
shown in fig. 17 over a 4 litre capacity container to
drain the hydraulic oil off. Recycle carefully! Dis-
pose of the waste oil in an environmentally friend-
ly manner!
4. Turn your machine on the motor side as shown in
Fig. 18 to refill about 2,4 l fresh oil.
5. Clean the oil drain screw with dipstick (8) and
screw it back in to the machine that is still in a
vertical position. Unscrew it again; there should
be an oil film between the two notches. (Fig. 15)
6. Now screw the oil drain screw with dipstick back
in tightly. Afterwards start splitting without actually
splitting log several times.
7. Check the oil level one last time and top up with a
little oil if required.
Dispose of the used oil in a correct manner at a
public collection facility. It is prohibited to drop
old oil on the ground or to mix it with waste.
We recommend oil from the HLP 32 range.
Connections and repairs
Connections and repairs of electrical equipment may
only be carried out by an electrician.
Please provide the following information in the event
of any enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: splitting wedge guides, hydraulic oil,
splitting wedge
* Not necessarily included in the scope of delivery!
Содержание 5805201984
Страница 6: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 6 14 11 12 13 4 3 g 10 E F ...
Страница 7: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 7 MAX MIN 16 17 18 15 8 8 ...
Страница 44: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 44 ...
Страница 45: ... www scheppach com service scheppach com 49 08223 4002 99 49 08223 4002 58 45 ...
