background image

5.5 TON LOG SPLITTER 1050mm caPacITy

Model no: 

LS1050V

Thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these 

instructions, and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SafETy

1.1.    

ELEcTRIcaL SafETy

 

‰

  

WaRNING!

 It is the user’s responsibility to check the following:

 

Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and    

 

all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical  

 

products. You may obtain an RCd by contacting your local Sealey dealer. 

 

If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable  

 

 

Appliance Test) tested.

 

Electrical safety information, it is important that the following information is read and understood.

1.1.1.   

ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. 

1.1.2.   

Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

1.1.3. 

  

Important

: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the    

 

correct fuse - see fuse rating in these instructions.

 

8

   DO  NOT

 pull or carry the appliance by the power cable.

 

8

  

DO NOT

 pull the plug from the socket by the cable. 

 

8

   DO  NOT

 use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or is 

  replaced immediately by a qualified electrician.

1.1.4. 

  

This product is fitted with a BS1363/A 13 Amp 3 pin plug. 

        

 If the cable or plug is damaged during use, switch the electricity supply and remove from use. 

        

 Ensure that repairs are carried out by a qualified electrician.

        

 Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.

 

 a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 

 b) Connect the BROWN live wire to the live terminal ‘L’.

 

 c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

       

 ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight. 

        

 Sealey recommend that repairs are carried out by a qualified electrician.

1.2.    

SafETy  aND maINTENaNcE.

 

9

   Keep the log splitter clean for best and safest performance.

 

9

   Maintain the

 

log splitter in good condition (use an authorised service agent).

 

9

   Use a qualified person to lubricate and maintain the log splitter.

 

8

  

DO NOT

 use brake fluid to top up hydraulic unit. 

 

8

  

DO NOT

 operate the log splitter if damaged.

 

9

   Replace or repair damaged parts. 

Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

1.3.    

WORKSHOP/ENVIRONmENTaL  SafETy.

 

 

9

   locate the log splitter on dry, level and solid ground in a suitable work area with adequate lighting.

 

9

   Keep the area clean and tidy and free from unrelated materials. 

DO NOT

 leave tools, logs or other items lying around where they could  

  become a tripping hazard.

 

8

  

DO NOT

 operate the log splitter in wet or damp areas or expose it to rain.

 

8

  

DO NOT

 operate the log splitter in areas where fumes from paint, solvents, or flammable liquids pose a potential hazard. 

1.4.    

OPERaTOR SafETy.

 

 

9

   Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain long hair.

 

9

   Wear protective, electrically non conductive gloves .

 

9

   Always wear safety goggles. everyday spectacles are not sufficient protection.

 

9

   Maintain correct balance and footing, 

DO NOT

 over-reach. ensure the floor is not slippery and wear non-slip, protective footwear.

 

8

  

DO NOT

 allow untrained persons to operate the log splitter.

 

8

  

DO NOT

 operate the log splitter with the guards or guides removed.

 

8

  

DO NOT

 operate the log splitter when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 

8

  

DO NOT

 attempt to load a log until the log pusher has returned to the stop position. 

 

9

   Stay alert and always pay attention to the movement of the log pusher.

 

9

   The log splitter must always be operated by one person only.

 

9

   Keep hands away from the moving parts of the log splitter.

 

9

   Keep hands away from splits and cracks which open in logs. They may close suddenly and crush or cut off parts of your hands.  

 

Recommended fuse rating

13 Amp

l

S1050V Issue 3 (HF) 25/06/18

Original Language Version

© Jack Sealey limited

Refer to 

instructions

 

Wear eye 

protection

 

Wear protective 

gloves

 

Wear safety 

footwear

 

Warning 

crushing of 

hands

 

Warning

Содержание LS1050V






Отзывы: