Scheppach 5801502903, Перевод с оригинального руководства пользователя

Страница: 24 / 60

24 GB
•
It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognized rules of safety.
•
Note the information published by your profession-
al associations.
•
Adjustable protective devices have to be adjusted
as close as possible to the workpiece.
•
Important! Support long workpieces (e.g. with a
roller table) to prevent them sagging at the end
of a cut.
•
Make sure the blade guard (3) is in its lower posi-
tion when the saw is being transported.
•
Safety guards are not to be used to move or mis-
use the machine.
•
Blades that are misshapen or damaged in any way
must not be used.
•
If the table insert is worn, replace it.
•
Never operate the machine if either the door pro-
tecting the blade or the detachable safety device
are open.
•
Ensure that the choice of blade and the selected
speed are suitable for the material to be cut.
•
Do not begin cleaning the blade until it has come
to a complete standstill.
•
For straight cuts of small workpieces against the
longitudinal limit stop the push stick has to be
used.
•
The bandsaw blade guard should be in its lowest
position close to the bench during transport.
•
For miter cuts when the table is tilted, the paral-
lel stop must be positioned on the lower part of
the table.
•
When cutting round timber, use a suitable holding
device to prevent the workpiece turning.
•
Never use guards to lift or transport items.
•
Ensure that the bandsaw blade guards are used
and correctly adjusted.
•
Keep your hands a safety distance away from the
bandsaw blade. Use a push stick for narrow cuts.
•
The push stick has to be stored on the intended de-
vice, so that it can be reached from normal working
position and is always ready to be used.
•
In the normal operating position the operator is in
front of the machine.
6. Technical data
Electro motor
220 - 240 V ~, 50 Hz
Power 750W
Revolutions 1400 min
-1
Saw band length 2240 mm
Saw band width 12,5 mm
Saw band width max. 15 mm
Cutting speed 720 m/min
Passage height 360 m/min
Passage width
0 - 175 mm
Table size 305 mm
Slewing range of the table 500 x 400 mm
Max. size of the workpiece 0° bis 45°
Overall weight
600 x 600 x 175 mm
Gewicht 74 kg
The work piece must have a minimum height of 3mm
and a minimum width of 10 mm.
The total noise values determined in accordance
with EN 61029.
sound pressure level L
pA
77,4 dB(A)
uncertainty K
pA
3 dB
sound power level L
WA
90,4 dB(A)
uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 61029.
7. Remaining hazards
The machine has been built using modern technolo-
gy in accordance with recognized safety rules. Some
remaining hazards, however, may still exist.
•
Risk of injury for fingers and hands by the rotating
saw band due to improper handling of the work
piece.
•
Risk of injury through the hurling work piece due
to improper handling, such as working without the
push stick.
•
Risk of damaging your health due to wood dust and
wood chips. Wear personal protective cloth such
as goggles. Use a fitting dust extractor.
•
Risk of injury due to defective saw band. Regu-
larely check saw band for such defects.
•
Risk of injury for fingers and hands while changing
saw band. Wear proper gloves.
•
Risk of injury due to starting saw band while
switching on the machine.
•
The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
•
Wear only closefitting clothes. Remove rings,
bracelets and other jewelry.
•
For the safety of long hair, wear a cap or hair net.
Even when all safety measures are taken, some
remaining hazards which are not yet evident may
still be present.
•
Remaining hazards can be minimized by follow-
ing the instructions in „General safety instructions“
„Proper Use“ and in the entire operating manual.