Scheppach 313795, Руководство по эксплуатации и технике безопасности

Страница: 43 / 80

35 GB/IE/NI
* Operating mode S6 40%: Continuous operation with inter-
mittent load (cycle time 10 min). In order not to heat the motor
more than permitted, the motor may only be operated for 40%
of the cycle time with the stated nominal power and must then
continue running for 60% of the cycle time without a load.
Noise emission values
Sound values were measured in accordance with EN 61029.
Sound pressure level L
pA
93,7 dB(A)
Uncertainty K
pA
3 dB
Sound power level L
WA
106,7 dB(A)
Uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total vibration
values (vector sum of three directions) determined according
to EN 61029.
9. Before putting into operation
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans - port dam-
age.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The machine must be securely installed, i.e. bolted down on
a workbench, base frame or similar.
• Before the machine is put into operation, all covers and safe-
ty devices must be properly attached.
• The saw blade must be able to move freely.
• In the case of wood which has already been worked with,
check for foreign bodies such as nails or screws etc.
• Before pressing the on/off switch, make sure that the saw
blade is correctly attached and that moving parts are free-
running.
• Before connecting the machine, check that the data on the
type plate matches those of the mains system.
• The machine must only be connected to a properly installed
safety socket which is protected by a fuse of at least 16A.
10. Assembly
m Warning! Risk of injury!
Improper installation of the circular table saw may result in seri-
ous injury.
Before commissioning, properly and completely install the cir-
cular table saw, including all covers and safety devices.
Never plug the mains plug into the power outlet before com-
pleting the installation.
If connections are secured with a hexagon screw, nut, spring
washer and washer, the washer and spring washer must be
fitted under the hexagon screw. The spring washer always lies
directly on the (inner) hexagon screw or nut. Hexagon screws
must each be inserted from outside inwards, and the connec-
tions must be secured from the inside with nuts. During assem-
bly nuts and screws must only be tightened until hand-tight, so
that they cannot fall out. If you tighten the nuts and screws fully
before final assembly, the circular table saw cannot be erected
in a correct and stable manner.
Assembling the frame and table width extender
(Fig. D-M)
1. Turn the table circular saw over and place it on the loor.
2. Insert the four legs (19) at the corner positions into the
device housing. Do not place any screws yet.
3. Now loosely screw the central struts (20) onto the legs
(19). Use the carriage bolts (b), the washers (c), the
spring washers (d) and the nuts (e) (Fig. G).
4. Screw the stand brackets (22) into the rear legs (19) us-
ing the drill holes. Assembly material for each: 2 carriage
bolts (b), the washers (c), the spring washers (d) and the
nuts (e) (Fig. I).
Caution! Both stand brackets must be at-
tached to the rear of the machine at attach-
ment points (23)! (Fig. E).
5. Loosely tighten the table width extender (6) on the saw
table (1) using the hexagon bolts with Phillips head (f).
(Fig. K).
6. Loosely tighten the table supports (24) on the housing
of the circular table saw. Use the hexagon screws (a),
hexagon screws (f), washers (c) and nuts (e).
Screw the four legs (19) and the table sup-
ports (24) onto the housing.
7. Align the table width and length extension lush with the
saw table.
8. Next, tighten all the screws of the legs (19) and the table
width extender (6).
9. Now attach the rubber feet (21) to the legs (19) (Fig. H).
10. Place the table circular saw on the base frame (11).
Mounting / adjusting the Riving Knife;
Caution! Remove the mains plug! The setting of the
saw blade (4) must be checked whenever a blade
has been replaced.
1. Adjust the saw blade (4) to a max. cutting depth, move to
the 0° position and lock in place.
2. Dismantle the saw blade guard (2) (not during initial as-
sembly).
3. Release the two attachment bolts (25) and remove the
table insert (5).
4. Loosen the fixing screws of the riving knife (26) (use the
open-ended spanner AF8 supplied).
5. Push the riving knife (3) upwards.
6. The distance between the saw blade (4) and riving knife
(3) should be between 3 mm and max. 5 mm, (Figure Q)
7. Retighten the fixing screws of the riving knife (26) and
mount the table insert (5).
8. Mount the saw blade guard (2) with the screw and
knurled nut and flat washer (27).