SCAN 58-1 Скачать руководство пользователя страница 5

Страница: 5 / 16

A S S E M B LY

Distance to flammable walls

Positioning your wood-burning stove

The wood-burning stove must be set up so that the stove itself, the flue pipe, and the chimney can all be cleaned.

Position near to non-flammable walls

When positioning near a non-flammable wall, we recommend you keep a minimum distance of 50 mm between the rear of the product and
the wall for cleaning purposes.

Distance to furniture: 1000 mm

But please check to avoid furniture or other furnishings being dried out due to being too close to the stove.

600

45° Corner installation

Parallel rear wall installation

600

350

Scan

58-3

& Scan

58-6

(with full lateral glass panes)

Parallel rear wall installation

Scan

58-2

& Scan

58-5

(with half lateral glass panes)

45° Corner installation

Scan

58-1

Scan

58-4

(without lateral glass panes))

Parallel rear wall installation

45° Corner installation

400

250

200

Содержание 58-1

















Результаты поиска

Содержание 58-1

Отзывы:

Бренды по названию

Популярные бренды

SCAN 58-1, Сборка и инструкция по эксплуатации

Результаты поиска

Содержание 58-1

Отзывы:

Бренды по названию

Популярные бренды