SCAN domestic SFO 4501, Руководство пользователя

Страница: 29 / 33

29
A hose that attaches to a sink spray can burst if it is installed
on the same water line as the dishwasher. If your sink has one,
it is recommended thet the hose be disconnected and the hole
plugged.
If the water pipes are new or have not been used for an extend-
ed period of time, let the water run to make sure that the water
is clear and free of impurities. If this precaution is not taken,
there is a risk that the water inlet can get blocked and damage
the appliance.
1 Turn off the water.
2 Unscrew The safety supply hose from the faucet.
Connection of the drain hose
Insert the drain hose into a drain pipe with a minimum diameter
of 4cm, or let it run into the sink, making sure to avoid bending
or crimping it. The free end of the hose must be at a height lower
than 60cm and must not be immersed into water to avoid the
backflow of it.
How to Drain Excess Water From Hoses
If the sink is more than 1000 mm higher than the floor, the ex-
cess water in hoses cannot be drained directly into the sink. It
will be necessary to drain excess water from hoses into a bowl or
suitable container that is held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly
fitted to avoid water leaks. Ensure that the water drain hose is
not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar
drain hose.
It must be no longer than 4 metres, otherwise the cleaning effect
of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height less than 1000 mm
(maximum) fromthe bottomof the dish. The water drain hose
should be fixed .
Start the dishwasher
The following things should be checked before starting the dish-
washer.
Installation steps
1 Connect the inlet hose to the cold water supply
2 Connect the drain hose. Refer to diagram
3 Connect the power cord
4 Affix the condensation strip under the work surface of cabi-
net. Please ensure the condensation strip is flush with edge
of work surface.
5 Place the dishwasher into position.
6 Level the dishwasher. The rear food can be adjusted from
the front of the dishwasher by turning the Allen screw in the
middle of the base of dishwasher use an Allen key. To adjust
the front feet, use a flat screw driver and turn the front feet
until the dishwasher is level.
7 The dishwasher must be secured in place. There are two
ways to do this:
Normal work surface: Put the right(left) installation hook
into the slot of the right(left) side plane and secure it to the
work surface with two woodscrews.
Marble or granite work top: Bend the right(left) installation
hook into right-angle,and put it into the slot of the right(left)
side plane and secure it to the work surface with two
woodscrews.
8 Bend the brackets of kick board according the depth to inser-
ted to the base , then fix the brackets to the kick board.
9 Insert the brackets to base of the dishwasher.
Leveling
Dishwasher must be level for proper dish rack operation and
wash performance.
1 Place a spirit level on door and rack track inside the tub as
shown to check that the dishwasher is level.
2 Level the dishwasher by adjusting the three levelling legs
individually.
3 When level the dishwasher, please pay attention not to let
the dishwasher tip over.
NOTE:
The maximum adjustment height of the feet is 50 mm.
Error codes
Before you call service, look at the following
When some malfunctions come on, the appliance will display
error codes to warn you:
Codes
Rapid indicator fleets frequently
• Longer inlet time.
• Faucets is not opened, or water intake is restricted,or water
pressure is too low.