SBG Navsight Apogee IMU Скачать руководство пользователя страница 42

Страница: 42 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

5.8.3. PORT D interface

PORT D interface is specific in the way that it is directly connected to the internal GNSS receiver.

PORT D shares all the common interfaces characteristics – see section PORT B and C interfaces for more
details.

In addition to that, the PORT D is the only port that can accept RTCM corrections for RTK operation.

5.8.3.1. Connector specifications (rugged)

The PORT B and C connectors use an 8 ways female ODU connector (ref G81F1C-P08LFG00000). Other
manufacturers such as Fischer provide compatible plugs (Fischer Core Series). The connector mates with
plug ref S31F1C-P08MFG0-5500.

Connector's pin out is the following:

Pin #

Name

Description

SHIELD

Connected to the mechanical ground

Not internally connected

SGND

PORT B or C Signal ground

TX+

RS-422 Tx+

TX- / TX

RS-422 Tx- / RS-232 Tx

RX+ / RX

RS-422 Rx+ / RS-232 Rx

RX-

RS-422 Rx-

SYNC IN D

Synchronization input D

+12V

+12V power supply output – may be used for radio modem power

5.8.3.2. Connector specifications (rack)

On the Rack version, the PORT D is accessible through a standard male DB-9 plug.

Pin #

Name

Description

SHIELD

Connected to the mechanical ground

SYNC_IN_D

Synchronization input D

RX+ / RX

RS-422 Rx+ / RS-232 Rx

TX- / TX

RS-422 Tx- / RS-232 Tx

SGND

PORT D Signal ground

RX-

RS-422 Rx-

TX+

RS-422 Tx+

42/74

Figure 5.14: External plug

Figure 5.13: Receptacle front panel view

Содержание Navsight Apogee IMU











































































Результаты поиска

Содержание Navsight Apogee IMU

Отзывы:

Похожие инструкции для Navsight Apogee IMU

Бренды по названию

Популярные бренды

SBG Navsight Apogee IMU, Руководство по оборудованию

Результаты поиска

Содержание Navsight Apogee IMU

Отзывы:

Похожие инструкции для Navsight Apogee IMU

Бренды по названию

Популярные бренды