SBG Navsight Apogee IMU Скачать руководство пользователя страница 51

Страница: 51 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

5.15. Typical connection topology

The following use cases are presented to quickly show how to connect the Navsight solution various
external equipment in different applications.

5.15.1. Navsight use in Land/Air survey applications

In this setup we use Navsight solution as navigation sensor for any land or air survey application

●

IMU can be installed remotely, where it’s convenient to the user (eg. close to LIDAR sensor)

●

Two antennas are connected directly on the Navsight processing unit

●

Serial RTK corrections are sent to Navsight unit through PORT D

●

If applicable, the odometer (DMI) pulses are connected to Navsight PORT E

●

Timing information is sent to LIDAR using standard ZDA message

●

Ethernet interface is used for

●

Real time data display on sbgCenter or any dedicated software

●

Get back the mission RAW data (IMU + GNSS) for post-processing purpose using Qinertia using
embedded FTP server

51/74

Figure 5.26: Navsight typical connections in an advanced automotive application

Ethernet network

SbgECom computer

→

RS-485 IMU connection

RS232 RTK

corrections

2x GNSS antennas

GGA + ZDA @ 1Hz

Odometer

LIDAR

Содержание Navsight Apogee IMU











































































Результаты поиска

Содержание Navsight Apogee IMU

Отзывы:

Похожие инструкции для Navsight Apogee IMU

Бренды по названию

Популярные бренды

SBG Navsight Apogee IMU, Руководство по оборудованию

Результаты поиска

Содержание Navsight Apogee IMU

Отзывы:

Похожие инструкции для Navsight Apogee IMU

Бренды по названию

Популярные бренды