Saturn KDB - 161 GOM Скачать руководство пользователя страница 81

Страница: 81 / 106

KDB-GOM

Series

- 81 -

Part name

Modulating gas control valve

Replacement steps

Disassemb

①

Unplug the boiler from the electric outlet and open the external cover.

②

Close the main gas valve installed on the gas supply pipe outside the boiler.

③

Loosen the flexible part connected to the gas inlet connection using manual tools (monkey spanner/group joint

plier).

④

Separate the four electric inlet wires connected to the gas control valve.

⑤

Separate the six wires connected to the gas control valve (4 ON-OFF valve, 2 proportional control valves ).

⑥

Separate the gas control valve and the nozzle by unscrewing the two screws connecting them.

⑦

Separate the board holding the ignition transformer and the air pressure switch from the nozzle by unscrewing

one screw.

⑧

Separate the gas control valve from the boiler.

sse

①

Fix the gas control valve to the external base.

②

Screw the four screws fixing the gas control valve to the external base.

③

Screw the two screws connecting the nozzle and the gas control valve (*check for the existence or

nonexistence of O-ring when connecting).

④

Assemble the parts making sure there is no gas leak.

⑤

Open the main gas valve.

⑥

Connect the six wires of the gas control valve correctly.

⑦

Fix the board holding the ignition transformer and the air pressure switch to the nozzle by screwing one screw.

⑧

Plug the boiler to the electric outlet.

Caution

  1. Check whether the gas pipe connecting O-ring is correctly assembled.
  2. Make sure not to switch the color of the connection terminals.
  3. Perform a gas leak test using soap foam after assembly.

⑧

⑦

⑥

④

Содержание KDB - 161 GOM











































































































Результаты поиска

Содержание KDB - 161 GOM

Отзывы:

Похожие инструкции для KDB - 161 GOM

Бренды по названию

Популярные бренды

Saturn KDB - 161 GOM, Руководство пользователя

Результаты поиска

Содержание KDB - 161 GOM

Отзывы:

Похожие инструкции для KDB - 161 GOM

Бренды по названию

Популярные бренды