SATO 6433-00 Скачать руководство пользователя страница 6

 

Installing and replacing batteries 

Install or replace batteries when firstly use of the unit or [BAT] mark is lit.   
(1)  Remove the battery cover by turning it clockwise with a coin or like. 

(2)  When replacing the batteries, remove the old batteries. 

(3)  Install new batteries with attention of the polarity marks (+ and -)   

(4)  Place batteries overlapping two batteries with the ‘+’ mark facing up.   

(5)  Reinstall the cover and tighten it by

 

turning it counterclockwise 

with a coin or like   

 

 

Cautions

 

-  The batteries are factory preset and since those batteries are for monitoring purposes, they may not last as 

long as general batteries. 

-  When the low battery mark blinks, replace new batteries. If you continue to use the unit with the mark 

blinking, malfunctions can occur. 

-  Do not dispose of used batteries in fire. 

-  Keep the batteries out of reach of children. If swallowed accidentally, consult a medical attention 

immediately. 

-  For environmental protection, dispose of used battery in compliance with local rules and regulations. 

-  For waterproof purpose, the lid of the battery compartment is fastened very tight. Be careful not to hurt 

yourself by using your fingernails to unfasten. 

-  Also be careful not to have any dust on the connecting area. If it is dirty, clean well before fastening. 

-  Do not let the unit get wet when the battery is removed. If water gets inside the unit, the instrument might 

get damaged. 

 

Before Measuring 

There is phthalate solution inside the cover avoiding the glass electrodes becomes dry.    Be careful not to 
spill when removing.    After the measurement, put the cover on the glass electrodes 

NB:

 When the unit is used for the first time or after it has been stored for several days, the pH measurement 

response may be slower. In such cases, immerse the sensor probe electrode in either the pH standard 
solution or water and let it stand for one hour. For more accurate measurement, immerse it 12 hours at 
least in the pH 4 standard solution before use.    (Turn off the unit during this immersion time.) 

 

(1) Removing the glass electrode protection bottle 
 

 Hold the sensor probe upright so as not to spill the standard solution in 

the protection bottle. Turn the protection bottle counterclockwise while 
pressing the cap. 

 
 
 

"

Protection bottle

Cap

Содержание 6433-00

















Отзывы: