background image

 

SATAM                                                                                                                                   Siège Social : Paris Nord II – 5, rue des Chardonnerets 
Usine de Falaise – Avenue de Verdun – B.P. 129 – 14700 FALAISE – France                   B.P. 85012 – Tremblay- en-France – 95931 Roissy C.D.G. Cedex - France 
Tél. : +33 (0)2 31 41 41 41                                                                                                      Tél. : +33 (0)1 49 90 77 00 
Fax : +33 (0)2 31 40 75 61                                                                                                      Fax : +33 (0)1 49 90 77 99  
SIRET 495 233 124 000 17                                                                                                    SA au capital de 6 037 000 € – RCS Bobigny B 495 233 124 
CODE APE 2813 Z                                                                                                                 SIRET 495 233 124 000 17 – Code APE  2813 Z – N° TVA : FR 48 495 233 124

 

 

SERIES 7888 METER PRINTER  

 

MANUAL  

DESCRIPTION - INSTALLATION - OPERATION - 

SERVICING

 

 

U508219-e – Revision 2 – 25 February 2009 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

This document consists of 

18

 pages, including the flyleaf

 

 

This document is the property of SATAM

 

And may not transmitted to third parties without prior authorisation

 

 

SATAM may modify this document without prior authorisation 

 

CONFORME à la directive européenne 94/9/CE – ATEX 

 

In conformity with the European directive 94/9/CE-ATEX 

Содержание 7888 Series



















Отзывы: