3
INSTALLER INFORMATION
The installation, all adjustments, transformations and maintenance listed in this part of the manual must be carried out
only by skilled personnel.
Improper installation may cause damage to persons, animals or property, for which the manufacture will not be held
responsible.
The appliance safety or automatic adjustment devices may be changed during the service life of the system only by the
manufacturer or by the duly authorised supplier.
INSTALLING THE COOKER
After having removed the various loose parts from the internal and external packing, make sure that the cooker is not damaged.
In case of doubt, do not use the appliance and contact skilled personnel.
Keep all the dangerous packing parts (polystyrene foam, bags, cardboard, staples, etc.) away from children.
The appliance can be installed as a freestanding unit, next to a wall at a distance of no less than 20mm (fig.2-Class 1
Installation) or inserted between two walls (fig 1-Class 2 Subclass 1 Installation). A single sidewall that exceeds the
height of the work surface is possible. This must be at a minimum distance of 70 mm from the edge of the cooker (fig.
2Class 1 Installation).
Any walls of the adjacent furniture pieces and the wall behind the cooker must be made with heat-resistant material that can
withstand a minimum over temperature of 65 K.
The appliance can be installed as class 1 and as class 2 subclass 1.
WARNING: when the appliance is installed as class 2 subclass 1, the connection to the gas network must only use
metal flexible pipes that conform with the national standards in force.
IMPORTANT INFORMATION FOR INSTALLING THE APPLIANCE
The cooker can be installed separately, as a freestanding unit, or between kitchen units or between a kitchen unit and
the wall. The device must be installed in accordance with the regulations stated in UNI 7129 and UNI 7131 standards.
This appliance is not connected to devices which exhaust combustion products.
Special attention must be focused on the prescriptions described below regarding room aeration and ventilation. Any
hanging cabinets installed above the work surface must be located at a distance of no less than 700 mm.
ROOM VENTILATION
To ensure that the appliance operate correctly, the room where it is installed must be continuously ventilated. The room volume
should not be less than 25 m³ and the quantity of air needed shall be based on the regular combustion of gas and on the
ventilation of the room. Natural air will flow through permanent openings in the walls of the room to be ventilated: these
openings will be connected with the outside environment and shall have a minimum cross-section defined by the current
national standards regarding room ventilation (see Fig. 3).
These openings shall be built so that they cannot be clogged.
Indirect ventilation is also permitted by taking air from the rooms adjacent to the one to be ventilated.
LOCATION AND AERATION
The gas cooking appliances must always evacuate the combustion products by means of hoods connected to chimneys, flues
or directly outside (see Fig. 4). If a hood cannot be installed, it is possible to use a fan installed on a window or directly facing
outdoors, to be operated together with the appliance (see Fig. 5), provided that there is strict compliance with the ventilation
regulations.
HEIGHT-ADJUSTABLE FEET (Fig.6)
(The feet are packed in the top box)
The feet should be installed with the cooker close to its final installation position; the feet are not safe to move the cooker long
distances. After unpacking the cooker, lift it with your foot, to fit the cooker feet in the bases at the bottom. Slowly lower the
cooker so its weight is resting on the feet and on the assembly fixings. We recommend using a lifting device or pallet instead of
tilting the cooker (
see instruction sheet in the supplied package)
..
INSTALLING THE TOEKICK PANEL (only available for some models)
After installing the feet, install the cooker skirt as shown in the pictures in Fig. 7 (
see instruction sheet in the supplied package)
.
INSTALLING THE RISER / BACK FRAME
see instruction sheet in the supplied
package
.
INSTALLING THE SYSTEM TO PREVENT OVERTURNING
To prevent the appliance from accidentally overturning, the system provided must be installed. Install the system as shown in
the figures. Figures 9-10
Содержание TS95C61LNE
