background image

TA2020B & IR2110B Installation Guide 

1 Introduction 

The TA2020B and IR2110B facilitate the transmission of data over ISDN networks.  

The units can be configured either by using commands entered at the serial port (much 
like a modem), or via the built-in Web interface. We recommend that you use the Web 
interface whenever possible. 

1.1 Front Panel Features 

The front panel of the unit incorporates number of LED indicators depending on the model 
as shown in the following illustration (IR2110B): 

 

Status Indicators 

The status indicators operate as follows: 

ON 

Illuminates steady red when power is applied. 

LAN 

On the IR2110B illuminates steady when there is a network 
connection to the LAN port and flashes when data is transmitted 
or received. 

ISDN: 
D, B1, B2 

Flash when data is transmitted/received over the ISDN D, B1 or 
B2 channels. 

DTE 0, 1 

Illuminate steady if a terminal is connected to the respective 
serial port and the DTR signal is on. Flashes when data is 
transmitted or received. DTE 1 is only present on the TA2020B. 

TA2020B & IR2110B Installation Guide 

Rear Panel Features 

The functions of these connectors are described in the following table: 

12V DC 

This jack socket is used to connect the unit to the power supply 
using 12V DC mains adapter. 

SERIAL 0 

This 25-way D socket provides a synchronous/asynchronous 
RS2322 serial port which may be used to connect the unit to a 
compatible serial device. The unit is supplied with a suitable 2 
metre serial cable. To comply with EMC requirements it should 
not be used with a longer cable. 

SERIAL 1 

On the TA2020B this 9-way D socket provides an asynchronous 
RS2322 serial port which may be used to connect the unit to a 
compatible serial device. The unit is supplied with a suitable 2 
metre serial cable. To comply with EMC requirements it should 
not be used with a longer cable. 

On the IR2110B, this port is disabled. 

LAN 

On the IR2110B this socket is used to connect the unit to a 
10/100-BaseT LAN using the 2-metre STP (Shielded Twisted 
Pair) cable supplied or a suitable alternative. This port is auto-
sensing for speed and wiring (straight-through or cross-over). To 
comply with EMC requirements it should not be used with non-
STP cable. 

ISDN 

This socket is used to connect the unit to an ISDN line. 

Reset switch 

This is located on the underside of the unit near the front. Pressing the switch gently with 
the tip of a pen or other suitable implement will generate a hardware reset. 

Содержание TA2020B









Отзывы: