Sapcon Vital Скачать руководство пользователя страница 9

User Manual & Datasheet V 2.3

10

Sensitivity Settings

The sensitivity settings can be set as per the requirement

using a DIP switch. The value of sensitivity is directly pro-
portional to the number of blinks. 1 blink is the equivalent to
the sensitivity value of 1. Thus, an increase in the number
of blinks will make the instrument more sensitive.

Note:

You can set the value of SENSITIVITY between 1-5.

Follow the below procedure for setting sensitivity

1. Ensure that all DIP switches are in OPEN position as

shown in Figure 6. Make sure that STATUS LED is not
blinking for Error.

OPEN

COVER

UNCOVER

SENSITIVITY

FAILSAFE

Figure 6: DIP Switch

2. To make the instrument sensitive, set the SENSITIV-

ITY switch to CLOSE position as shown in figure 7.
A small screw driver can be used for closing and open-
ing of DIP Switch. (CLOSE is the opposite of OPEN
for a DIP switch). The STATUS RED LED will glow.

OPEN

ENTER

COVER

UNCOVER

SENSITIVITY

FAILSAFE

VITAL

STATUS

LED

RED

GREEN

Figure 7: Sensitivity Switch Position

3. Press ENTER and keep it pressed as shown in Figure

8. The STATUS RED LED starts blinking. Count the
number of blinks. After setting the value release the
ENTER key.

5 blinks indicate highest sensitivity which is re-
quired for low density materials.

1 blink refers to lowest value of sensitivity which
is required for normal solids.

OPEN

ENTER

COVER

UNCOVER

SENSITIVITY

FAILSAFE

VITAL

STATUS

LED

RED

GREEN

Figure 8: Setting Sensitivity Value

4. The value of sensitivity is now entered, but not saved.

To save and test the sensitivity, set the SENSITIVITY
switch back to OPEN position as shown in Figure 9.
The STATUS LED will come back to its original posi-
tion.

OPEN

ENTER

COVER

UNCOVER

SENSITIVITY

FAILSAFE

VITAL

STATUS

LED

RED

GREEN

Figure 9: Saving Sensitivity Value

11

Cover Delay

When the application material covers the fork tines,

the changeover of the output can be delayed by a pre-
determined time. This time is called COVER Delay. For
a different value of Cover Delay, the number of blinks can
be adjusted as per requirement.

Note:

You can set the value of COVER DELAY between 1-
25 secs.

Follow the below procedure for setting Cover Delay

1. Ensure that all DIP switches are in OPEN position as

shown in Figure 6. Make sure that STATUS LED is not
blinking for Error.

2. To set the Cover Delay, set the COVER switch to

CLOSE position as shown in Figure 10.
(CLOSE is the opposite of OPEN for a DIP switch.)
The STATUS RED LED will glow.

OPEN

ENTER

COVER

UNCOVER

SENSITIVITY

FAILSAFE

VITAL

STATUS

LED

RED

GREEN

Figure 10: Cover Delay Switch Position

3. Press ENTER and keep it pressed as shown in Figure

11. The STATUS RED LED will start blinking. Count
the number of blinks. After setting the value release
the ENTER key.

4. Delay is entered, but not saved. To save and test the

Cover Delay, set the COVER switch back to OPEN po-
sition as shown in Figure 12. The STATUS LED will
come back to its original position.

5. To test, dip vital into the application material until the

switching point is reached.

Sapcon Instruments Pvt.Ltd.

R

9

Содержание Vital














Отзывы: