Sanyo SAP-CM1821A Скачать руководство пользователя

Страница: 49 / 62

Using the Remote Control Unit (continued)

Mounting the Remote

Control Unit

Mounting on a wall

A. Removable mounting

1) Momentarily hold the remote control unit at the desired

mounting position.

2) Confirm that the air conditioner responds correctly when you

press keys on the remote control from that position.

3) After confirming correct operation, use a screwdriver to screw

the mounting screw into the wall.

4) Hang the remote control unit from the mounting screw.

B. Non-removable mounting

1) Momentarily hold the remote control unit at the desired

mounting position.

2) Confirm that the air conditioner responds correctly when you

press keys on the remote control from that position.

3) After confirming correct operation, use a screwdriver to screw

the mounting screw into the wall.

4) Remove the batteries of the remote control unit.

5) Use a screwdriver to screw the remote control unit securing

screw into the wall through the hole in the battery compartment.

6) Replace the batteries.

7) Again confirm that the remote control unit operates correctly.

(Packed in the
indoor unit)

Removable mounting

Non-removable mounting

Wall

OI-226-11EG

Содержание SAP-CM1821A































































Результаты поиска

Содержание SAP-CM1821A

Отзывы:

Похожие инструкции для SAP-CM1821A

Бренды по названию

Популярные бренды

Sanyo SAP-CM1821A, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-CM1821A

Отзывы:

Похожие инструкции для SAP-CM1821A

Бренды по названию

Популярные бренды