Sanyo SAP-CM1821A Скачать руководство пользователя

Страница: 43 / 62

Names of Parts

NOTE

This illustration is based on the external appearance of a standard
model. Consequently, the shape may differ from that of the air
conditioner you have selected.

This air conditioner consists of an indoor unit and an outdoor unit.
You can control the air conditioner with the remote control unit.

Air Intake

Air from the room is drawn into these sections and passes
through air filters which remove dust.

Air Outlet

Air is blown out of the air conditioner through the air outlet.

Remote Control Unit

The

wireless

remote

control

unit

controls

power

on/off,

operation mode selection, temperature, fan speed, timer setting,
and air sweeping.

Refrigerant Tubes

The indoor and outdoor units are connected by copper tubes
through which refrigerant gas flows.

Drain Hose

Moisture in the room condenses and drains off through this
hose.

Outdoor (Condensing) Unit

The outdoor unit contains the compressor, fan motor, heat
exchanger coil, and other electrical components.

INDOOR UNIT

Air intakes

Air outlet

Remote
control
unit

Drain hose

Refrigerant
tubes

OUTDOOR UNIT

Air outlet

OI-226-05EG

Содержание SAP-CM1821A































































Результаты поиска

Содержание SAP-CM1821A

Отзывы:

Похожие инструкции для SAP-CM1821A

Бренды по названию

Популярные бренды

Sanyo SAP-CM1821A, Техническое и сервисное руководство

Результаты поиска

Содержание SAP-CM1821A

Отзывы:

Похожие инструкции для SAP-CM1821A

Бренды по названию

Популярные бренды