Sanwa MT-44, Руководство пользователя

Страница: 50 / 68

Push
４９ ５０
Usa
ge of ea
ch function
Usage of ea
ch fea
ture
System Menu
●A feature for setting system of the transmitter, such as Bind (BIND), Key Assignments
(KEY ASSIGN), BUZZER (Buzzer), Battery (BATTERY), LCD and CALIBRATION (Calibration).
●Select the output system that suits the receiver, set a mode for the servo (analog/digital) and
the speed controller to be used and bind the transmitter with the receiver.
1)Select [SYSTEM] with the multi-selector and determine
with the Enter operation.
2)Select [BIND] with the multi-selector and determine
with the Enter operation.
3)Setting RF MODE (RE MODE: Signal output system)
Set the output system with the multi-selector.
○ Output System
・
FH4T
RX-482, RX-481, RX-472, RX-471, RX-47T
RX-462, RX-461, Mode for SV-PLUS series
・
FH3
RX-451R, RX-451, RX-381, Mode for RX-380
○Output System
*When changing the output system, a message is displayed
on the screen. Follow the display to operate.
4)Setting TELEMETRY
Set TELEMETRY with the multi-selector.
Setting range: ON/OFF
○Default : ON
*Telemetry Compatible Equipment
・ RX-482 、 RX-472 、 RX-47T 、 RX-462 、 RX-461 、 SV-PLUS series
*Re-BIND is not necessary even if setting is changed.
[BIND]
ENTER BACK
ENTER
ENTER BACK
5)Setting SAFETY LINK
Set SAFETY LINK (Safety Link) with the multi-selector.
○ Setting range: 01 ~ 50
○ Default : 01
*When changing the setting of SAFETY LINK after BINDING, BIND again.
Output System
●A feature for preventing runaway due to an error of Model Select. You can set a Link No. for each Model
●When performing Model Copy (FULL), the Link No. is also copied.
●Default is set to [01]. When Link No. is not being changed, receivers that are BINDED will be working for all models
●Safety Link works only for [FH4T].
Supplement
5)Setting Channel Mode
Set the response mode for each channel with Up key/Down key.
・
You can the set the response mode for each channel.
○Setting range: NOR (Normal)
SHR (High Response)
SSR (Super Response)
○Default : NOR
*The response mode of SSR is displayed only when FH4T is set.
●Note that, in SHR/SSR mode, an analog servo will not work. If you mistakenly use an analog servo in SHR/SSR mode, it will not operate
normally and the servo will be broken. Do not use an analog servo in SHR/SSR mode. For digital servo (SRG, ERB ERS series, Digital
ERG series), it can work for either mode of NOR/SHR.
●SSR mode works only for SRG servo, SUPER VORTEX/SV-PLUS series, HV-12 STOCK SPECIAL and HV-01.
●SSR mode cannot be used in MT-44 even if RX-451R is used to BIND on the SHR display. It will act as it is shown in the display.
●In SHR/SSR mode, BL/RACER, BL/FORCE, F2000, F2200, F3000, F3300, SBL-01, 02 and 03CL do not work.
●SV-08, HV-10, HV-12 and F2500 work in NOR/SHR mode.
Important
Flashing
NOTE)The above picture don’t have wiring.
However, before binding, please connect
servo, FET ESC (without motor), battery.
Holding BIND button
of recevier,
Turn Power Switch ＯＮ！
ＰＵＳＨ！
ENTER
⇒
(Flashing with approximately 0.5-second interval)
Status of the Receiver LED
(High-speed flashing)
(Light goes off)
・・・・・・・・・・・・・・・・・・ ・・・・・・・・・・・・・・・・・ ・・・・・
BINDING Complete
(Light on)
Note
●BINDING is not done at the factory. Please make sure to complete BINDING before use.
●When the receiver is new, make sure to complete BINDING for the transmitter and the new receiver.
●Make sure to use the set of the transmitter and the receiver that completed BINDING.
●When BINDING RX-451, R-451R, RX-381 and RX-380, set RF-MODE (output system) to FH3 to BIND.
●If you use a receiver of a wrong type or make a wrong setting of MODURATION, you cannot perform BINDING.
●When changing the setting in the BIND menu after BINDING, repeat BINDING.
●RX 481 and RX-471 work for either FH4T or FH3, but use with FH4T to have the receiver’s original performance.
●When changing the setting of the mode (NOR/SHR/SSR) after BINDING, repeat BINDING.
If you do not re-BIND, setting changes will not be reflected.
Push
Response Mode
Output System
Confirmation Screen
6)Setting BIND (Bind)
●What is BIND: Each of MT-S transmitters has its own unique ID (solid identification) number. BIND is to let
the receiver memorize the ID number. Operation will be possible only between the transmitter and the
receiver that completed Binding.
1]When setting in the BIND menu is done, set BIND
with the multi-selector.
2]Move the cursor to [ENTER] in the BIND menu and operate
Enter. The transmitter now is ready for BIND operation.
3]Turn the power switch on while holding the BIND button of the receiver.
4]When BINDING is done properly, the LED of the receiver starts
flashing slowly at first then it flashes in high speed and the LED
goes off. When the LED of the receiver goes off, operate the
Enter key of the transmitter to complete BINDING of the transmitter.
When BINDING is done properly, the LED of the receiver is lit.
When the LED of the receiver is lit, activate the servo to check if
BINDING is completed.
*When BINDING cannot be done properly, restart from step 2).
Turn on the power switch of
reciever/FET ESC.
Usage of each feature
SYSTEM