background image

Exhaust Filter

11

Look for the

   symbol.

GENUINE

EUREKA PRODUCT

HOW TO MAINTAIN 

(continued)

NOTE:  Turn off the switch and unplug the electrical cord before servicing the

cleaner. Never operate the vacuum cleaner without the dust bag or filters.

FILTERS

Motor Filter

The motor filter is located below the dust bag
inside the bag compartment. Remove the
front cover. Take the dust bag out to check
the motor filter. If the motor filter is dirty,
remove and clean or replace with a new filter.

To clean the motor filter, brush the debris off
into a trash bin or vacuum with another
vacuum cleaner.

1

2

1

The filters should be checked at each disposable dust bag change. If the filters are
dirty, clean or replace for maximum performance of your cleaner.

Front Cover

The exhaust filter is located behind the dust
filter grille below the bag compartment.

Remove the front cover. (The front cover has
to be removed first to enable removal of
exhaust grille.) Lift up on exhaust grille handle
to remove. The filter is attached to the back
of the grille. If the exhaust filter is dirty, remove
and clean or replace with a new filter.

To clean the exhaust filter, brush the debris
off into a trash bin or vacuum with another
vacuum cleaner.

To replace the exhaust filter, tuck the bottom
of the filter behind the two filter retainers at
the bottom of the exhaust grille. Then place
the top of the filter behind the two filter
retainers at the top of the grille. Press the
filter down on narrow pegs in the center of
the grille. Replace the grille on the cleaner
and replace the front cover.

2

Lower
Filter
Retainers

Exhaust
Grille
Handle

Upper Filter

Retainers

Содержание SC785 SERIES

















Отзывы: