SBOX-5210 - User Guide, Rev. 1.0
// 31
Visually check that each lever latch is fully closed and correctly engaged with the notch
on the memory module edge.
6.
Repeat step 2 - 5 to install the second SO-DIMM memory module in case two DIMM memory modules are required.
Use memory modules with the same memory density in both socket!
In case two memory modules are installed, install the module to the lower socket first.
In case only one memory module is installed, we suggest installing it on the lower
socket.
7.
In order to close the device, proceed step 10 - 13 described in the subsection 5.1 "Opening and Closing the Chassis".
5.1.2.
Installing A HDD / SSD
To install a 2.5" HDD / SSD please proceed according to the steps described:
1.
Open the device as described in the subsection 5.1 "Opening and Closing the Chassis" (step 1 - 9).
2.
Place the HDD / SSD into the hard disk tray.
3.
Align the screw holes located on the back side of the HDD / SSD with the screw holes (Figure 8, pos. 1) of the hard
disk tray and then screw the HDD / SSD to the tray with four M3x3.5 screws.
4.
Connect the SATA data + power combo connector (Figure 5, pos. 5) to the HDD / SSD. In case the SATA data +
power cable (Figure 5, pos. 4) is packed separately, connect the SATA data plug (Figure 5, pos. 6) and hard drive
power plug (Figure 5, pos. 7) to the onboard SATA data connector (Figure 5, pos. 2) and hard drive power
connector (Figure 5, pos. 3) respectively.
5.
In order to close the device, proceed step 10 - 13 described in the subsection 5.1 "Opening and Closing the Chassis".
5.1.3.
Installing An M.2 SSD
To install an M.2 SSD please proceed according to the steps described:
1.
Open the device as described in the subsection 5.1 "Opening and Closing the Chassis" (step 1 - 9).
2.
Locate the M.2 Key M socket (Figure 5, pos. 9) and the corresponding fixing bolt (Figure 5, pos. 11).
3.
Align the notch on the M.2 SSD with the notch in the M.2 socket. Insert the M.2 SSD into the corresponding socket
and rotate it down with the fixing hole of the M.2 SSD over the fixing bolt.
4.
Press the M.2 SSD down on the side with the fixing hole and secure it with the available fastening screw.
5.
In order to close the device, proceed step 10 - 13 described in the subsection 5.1 "Opening and Closing the Chassis".
5.1.4.
Installing An M.2 WLAN / Bluetooth Module
To install an M.2 WLAN / Bluetooth module please proceed according to the steps described:
1.
Open the device as described in the subsection 5.1 "Opening and Closing the Chassis" (step 1 - 9).
2.
Locate the M.2 Key E socket (Figure 5, pos. 8) and the corresponding fixing bolt (Figure 5, pos. 10).
3.
Align the notch on the M.2 WLAN / Bluetooth module with the notch in the M.2 socket. Insert the M.2 WLAN /
Bluetooth module into the corresponding socket and rotate it down with the fixing hole of the module over the
fixing bolt.
4.
Press the M.2 WLAN / Bluetooth module down on the side with the fixing hole and secure it with the available
fastening screw.
5.
In order to close the device, proceed step 10 - 13 described in the subsection 5.1 "Opening and Closing the Chassis".
