manualshive.com logo in svg

S&C PureWave AVC, Инструкция по установке и эксплуатации

Поделиться
Скачать
S&C PureWave AVC Скачать руководство пользователя страница 21

21

656-500

Start Up

Upon energizing the PureWave AVC in RUN Mode, or after a power out-
age, the microprocessor controller starts automatically; firing of the
thyristors is prevented. A self-calibration routine is executed. Once the
proper firing sequence of the thyristors has been determined, the Pure-
Wave AVC goes into automatic steady-state operation. Start-up time is
approximately 30 seconds.

To start up the PureWave AVC:

1. Place the 

STANDBY/RUN

  switch on the control section in the

RUN

 position. See Figure 16.

2. If a circuit breaker has been furnished in the PureWave AVC,

press the 

CLOSE

  push button on the control section. (In some

configurations, 

OPEN

  and 

CLOSE

  push buttons may be

mounted on the control section door. If a circuit breaker has not
been furnished in the PureWave AVC, close the external circuit
breaker or disconnect switch.

Off-Line Operation

The PureWave AVC can be operated in standby mode to permit control
system configuration. In this operating mode, triggering signals to the
SCRs are disabled.

To  operate the PureWave AVC off-line: Place the 

STANDBY/RUN

switch on the control section in the 

STANDBY

 position. See Figure 16.

To  again operate the PureWave AVC on-line: Place the

STANDBY/RUN

 switch on the control section in the 

RUN

 position.

Ç

 

DANGER

This equipment contains high voltage. Do not attempt to access the
interior of the control section or capacitor section(s) when the Pure-
Wave AVC is energized. Failure to observe this precaution may result
in serious injury or death.

OPERATING PROCEDURE

STANDBY/RUN 

Figure 16. Control panel.

Содержание PureWave AVC

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды